Small Group Tutorials

Here to help students catch up, keep up, and move ahead. Book a consultation here.

Top 100 Secondary 4 G3 Vocabulary List for Punggol | Design and Technology: Design Decisions, Materials and Mechanisms

Three students in school uniforms work through open books at a classroom table, with textbooks and stationery nearby and study notes on the whiteboard behind them.

This Top 100 Secondary 4 G3 Vocabulary List for Punggol helps students explain Design and Technology decisions clearly. Learn the words that connect a user’s need to a workable design: specifications, material properties, forces, mechanisms and testing. Each term has an accessible meaning and an application check, followed by worked examples and independent questions to show what needs further practice.

The guide supports cumulative upper-secondary revision for 2027 SEC G3 Design and Technology, syllabus K345. It is an independently selected teaching list, not an official SEAB ranking or a complete syllabus checklist. Use it alongside school lessons and project instructions, starting with the words that prevent you from explaining your own design decisions. The examples are original learning situations; they are not examination questions or proposed answers for an assessed project.

  • Start with meaning: distinguish a need, a specification, a material property and a test result.
  • Use all four columns: explain the term, apply it, then change one condition and reconsider your answer.
  • Check understanding: try the eight independent questions before reading the answers.
  • Choose the next action: use the diagnostic table to repair the particular error you find.
  • For parents: ask for an explanation of one decision; keep project thinking and recorded work the student’s own.
  • Course scope: check the school’s sequence and current instructions against the linked official K345 syllabus.

Choose your next learning step

Use the route that answers your question today, then continue through the full guide.

Full chapter index · Independent practice · 200-term D&T reference

Full contents

Understand and learn
  1. What this vocabulary guide helps you do
  2. The 100 D&T terms and their applications
  3. Common confusions that change a design answer
Apply and revise
  1. Five worked examples: from word to reasoned decision
  2. Independent practice and explained answers
  3. A manageable vocabulary revision routine
Plan support and check sources
  1. How parents and teachers can help
  2. Questions students and parents often ask
  3. Official sources and where to continue

CHAPTER 1 OF 9

What this vocabulary guide helps you do

Back to contents

D&T words become useful when they connect a reason to a choice. A student who writes “the material is strong” has named a possible advantage, but has not yet explained the expected load, the relevant type of strength or the alternatives considered. The missing part may be a word, a concept or a link between the two. This guide helps you identify that missing part before adding more notes.

For example, a card holder may bend without breaking, tip without bending, or remain upright while being uncomfortable to use. These are three different problems. Stiffness, stability and ergonomics help you describe them accurately. Once the problem has a precise name, you can investigate an appropriate change and explain why that change should help.

The official 2027 K345 syllabus combines design and technological understanding. It includes materials and workshop processes, structures, mechanisms and electronics. Its assessment has a two-hour written paper worth 40% and a design project worth 60%, conducted over 22 weeks excluding school holidays. These are course facts, not a suggested home revision timetable.

The SEAB 2027 G3 directory is the starting point for checking the current subject document. Confirm your registered subject and examination year with school. A Secondary 4 student may be revisiting ideas learned earlier, while another class may be developing them in a different project. The order of this list is a learning route, not a national week-by-week teaching sequence.

Separate three kinds of difficulty

A vocabulary difficulty means you cannot explain a word accurately. A conceptual difficulty means you can repeat the definition but cannot recognise the idea in a new situation. A communication difficulty means you understand the decision but leave its reasoning out of your answer. These can occur together, but they need different practice. Read a definition for the first, compare examples for the second, and explain a complete decision for the third.

Begin with one recent piece of work. Circle a sentence that feels vague, such as “I made it better”. Ask what changed, what problem it addressed and what evidence supports improvement. “I lowered the front edge because it obstructed card retrieval in the mock-up” tells the reader far more. You do not need an impressive adjective when the reasoning is already precise.

For a wider reference bank, use the 200-term G3 D&T vocabulary guide. The task here is narrower: check whether you can use selected words independently and decide what to practise next. You do not need to memorise both lists before attempting a useful explanation.

Contents · Next chapter

CHAPTER 2 OF 9

The 100 D&T terms and their applications

Back to contents

Cover the meaning column and explain one term in ordinary language. Then answer its application prompt. Each numbered entry counts as one headword or established technical phrase; numbering helps navigation and does not rank importance. The brief definitions are starting points for reasoning, so use the conditions in your actual question or design situation.

Understanding a person and a problem

No.TermMeaningUse, check or example
1UserThe person who operates, handles or benefits from a product in its intended situation.Describe the actual user of a card holder. The person buying it may have different needs from the person using it.
2NeedA difficulty or requirement that a design should address for a particular person or situation.Cards falling from a desk create a storage need. Establish when and why that happens before choosing a container.
3WantA preference that a person would like a design to satisfy.A blue finish may be a preference. Ask whether colour also communicates information before treating it as purely decorative.
4ContextThe circumstances in which an activity or product is used, including the place and surrounding conditions.A holder used on a crowded desk faces different space constraints from the same holder on a wide display counter.
5Design opportunityA situation in which a purposeful change could improve an activity, experience or product.Notice repeated difficulty retrieving cards with one hand. Explain the opportunity without assuming that a motor is the answer.
6ObservationCareful watching and recording of what happens during an activity.Record where a user reaches and what obstructs the movement. Separate what you saw from your explanation of it.
7InterviewA planned conversation used to learn about a person’s experiences, needs or views.Ask what makes the current holder difficult to use. A question that suggests your preferred answer gives less useful evidence.
8EmpathyAn effort to understand another person’s experience and perspective.Ask the user to explain their difficulty. Your own comfortable grip does not establish that the product suits their hands.
9EvidenceInformation used to support a conclusion or design decision.A recorded observation can support a change in handle position. Identify which observation supports which change.
10ConstraintA limit within which the design must work.A maximum desk footprint is a constraint. Show how a proposed wider base would fit, rather than ignoring the limit.
1–10: Understanding a person and a problem

Turning a need into a design decision

No.TermMeaningUse, check or example
11Design briefA concise statement of the design opportunity, intended user and purpose of the proposed work.State who needs help with which activity. Avoid describing every construction detail before alternatives have been investigated.
12Design specificationA set of requirements used to guide development and judge a proposed solution.Replace “easy to use” with a requirement that can be checked with the intended user under stated conditions.
13CriterionA standard or feature used when judging a design; the plural is criteria.Ease of card retrieval is one criterion. Explain how you will judge it instead of attaching an unsupported score.
14FunctionThe intended job that a product or component performs.The holder stores cards and allows retrieval. A decorative panel should not obstruct either part of that function.
15AestheticsThe qualities that shape how a design is perceived through its appearance and other sensory features.Explain how proportion, colour or texture suits the setting. “Looks nice” leaves the reader guessing about the design choice.
16ErgonomicsDesigning products and tasks to fit people’s capabilities, comfort and limitations.Check reach, grip and visibility together. A handle of suitable size can still be awkward if its position forces a poor movement.
17Anthropometric dataMeasurements of human bodies or body parts used to inform design.Hand measurements can inform a grip. Use data relevant to the intended users rather than assuming everyone matches an average.
18AccessibilityThe extent to which intended users, including people with differing abilities, can use a design.Consider whether the label can be read and the cards reached. Do not assume that solving one barrier removes every barrier.
19SustainabilityConsidering environmental, social and resource consequences over a product’s life.Compare repair, useful life and material use. A recycled label alone does not settle which design has the better overall outcome.
20Trade-offA choice in which improving one desirable feature involves a disadvantage or cost elsewhere.A wider base may resist tipping but occupy more desk space. State which requirement matters most in the given context.
11–20: Turning a need into a design decision

Generating and communicating ideas

No.TermMeaningUse, check or example
21IdeationGenerating possible ways to respond to a design opportunity.Sketch several arrangements for retrieving cards. Changing only the colour of one arrangement offers little functional variety.
22BrainstormingGenerating a range of ideas before selecting and developing the more promising ones.Record a pull-out tray, a tilted pocket and a divided rack before judging their suitability against the requirements.
23SCAMPERIdea prompts: substitute, combine, adapt, modify, put to other uses, eliminate, and reverse or rearrange.Try eliminating an obstructing lid. Explain whether the resulting open holder still protects the cards adequately.
24IterationRepeating and revising aspects of a design in response to what is learned.After a mock-up reveals poor access, change the opening and test again. Record the reason for the change.
25SketchA drawing used to explore or communicate an idea.Draw the holder from an angle that reveals its opening and support. A useful thinking sketch need not be a polished picture.
26AnnotationA note attached to a drawing or image that explains a feature, reason or requirement.Explain why the front edge is lower. Repeating “front edge” beside an obvious line adds little useful information.
27Isometric drawingA three-dimensional representation using three principal axes equally spaced at 120 degrees.Use it to show how the sides and base relate. Add necessary dimensions when communicating construction details.
28Orthographic drawingA representation using separate two-dimensional views projected perpendicular to the viewing planes.Align front, top and side views so that a component’s dimensions and features can be understood consistently.
29Exploded viewA drawing that separates components visually while showing how they fit together.Use it to explain an assembly. The drawn separation is for communication; it is not a gap required in the finished product.
30Sectional viewA drawing showing an imagined cut through an object to reveal internal features.Use a section to explain a hidden slot or wall thickness that an outside view does not show clearly.
21–30: Generating and communicating ideas

Modelling, measurements and project records

No.TermMeaningUse, check or example
31ModelA representation used to explore or communicate selected features of an idea.A paper model can reveal proportions. Explain which properties it represents and which it cannot reproduce.
32Mock-upA quick, often simplified model made to investigate a feature or arrangement.A cardboard opening can test hand access. It cannot establish the final material’s resistance to repeated loading.
33PrototypeA developed version used to demonstrate and investigate how a proposed solution works.State which functions the prototype demonstrates. Looking complete does not prove that every specification has been achieved.
34ScaleThe ratio between a representation’s dimensions and the corresponding real dimensions.At a scale of 1:2, a 100 mm feature is drawn 50 mm long. Check whether a model permits meaningful user testing.
35DimensionA stated measurement defining size, position or distance.Label the internal width needed for cards as well as the overall width. The two dimensions answer different questions.
36ToleranceThe permitted variation from a specified dimension or value.If a practice drawing states 80 ± 1 mm, its acceptable interval is 79–81 mm. This is an example, not a universal allowance.
37DatumA chosen reference point, line or surface from which measurements are taken.Dimension several holes from one suitable reference edge. Explain how that avoids accumulating separate marking errors.
38Gantt chartA chart showing planned activities against time.Show testing before final evaluation and leave time for justified changes. Update the plan when an activity takes longer.
39Design journalA record of investigations, developing ideas, decisions and progress during a design project.Keep the observation and the resulting change together. The reader should be able to follow how your thinking developed.
40Presentation boardA visual communication of the proposed solution and its relevant features.Show the product in use and explain the important details. A striking image without functional information is incomplete.
31–40: Modelling, measurements and project records

Material properties

No.TermMeaningUse, check or example
41PropertyA characteristic describing how a material behaves or responds under particular conditions.Name the relevant property before selecting a material. “Good quality” does not explain behaviour in the proposed product.
42StrengthThe ability to withstand stress without yielding or failing, according to the type of loading considered.Explain whether a part must resist pulling, bending or another load. Strength alone does not tell you how much it will deflect.
43StiffnessResistance to elastic deformation under an applied load.A shelf that bends too much may need greater stiffness. It can be unacceptably flexible even if it has not broken.
44HardnessResistance to local indentation, scratching or similar surface deformation.A desk-facing surface may need scratch resistance. Do not use hardness as a substitute for resistance to sudden impact.
45ToughnessThe ability to absorb energy and deform before fracturing.For a part that may receive an impact, toughness can matter. A hard material can still fracture with little energy absorption.
46ElasticityThe ability to return towards the original shape after a load is removed, within the elastic limit.A spring that returns after a small deflection shows elastic behaviour. Excessive loading may produce permanent deformation.
47DurabilityThe ability to remain serviceable over time under expected conditions of use.Consider moisture, wear and repeated operation. A successful first use does not establish long-term durability.
48DensityMass per unit volume of a material.For equal volumes, a denser material has greater mass. Compare actual dimensions before claiming one complete product is lighter.
49CorrosionDeterioration of a material, commonly a metal, through chemical or electrochemical interaction with its environment.Consider the environment and protective finish. Rust is a particular corrosion product associated with iron and steel.
50Material selectionChoosing a material by relating its properties and practical implications to the design requirements.Compare performance, manufacture, availability and cost. State the disadvantage you accept as well as the benefit you seek.
41–50: Material properties

Material families and examples

No.TermMeaningUse, check or example
51Natural timberWood taken from trees and prepared for use while retaining its natural grain structure.Consider grain direction and possible variation. Two pieces of the same named timber need not behave identically.
52PlywoodAn engineered board made by bonding thin wood layers, usually with adjacent grain directions crossing.The layered structure can improve dimensional stability. Grade and adhesive affect suitability; plywood is not automatically waterproof.
53Medium-density fibreboardAn engineered wood panel made from wood fibres bonded together; often abbreviated MDF.Its fairly uniform structure can suit some modelling tasks. Assess moisture exposure and follow workshop controls for dust.
54ThermoplasticA polymer material that can soften when sufficiently heated and harden again when cooled.Explain why reshaping may be possible. The word does not mean that any thermoplastic is safe for every heating process.
55Thermosetting plasticA polymer material that forms an extensively cross-linked structure and cannot simply be remelted after curing.Compare it with a thermoplastic. Heating a cured thermoset does not restore the original mouldable state.
56AcrylicA commonly used thermoplastic available in transparent and coloured forms.Transparency may help users see stored cards. Consider impact behaviour and edge treatment before deciding it is suitable.
57Ferrous metalA metal or alloy in which iron is the main constituent.Mild steel is an example. Do not assume every ferrous material has identical corrosion resistance or magnetic behaviour.
58Non-ferrous metalA metal or alloy in which iron is not the main constituent.Aluminium and copper belong to this broad group. The category alone does not determine strength, cost or suitability.
59AlloyA metallic material containing two or more elements, at least one of which is a metal.Brass combines copper and zinc. Explain the relevant properties of the particular alloy rather than treating all alloys alike.
60CompositeA material made from distinct constituents combined to obtain useful properties.A fibre-reinforced material combines reinforcement and a surrounding matrix. Identify what each contributes to the behaviour.
51–60: Material families and examples

Forces and structures

No.TermMeaningUse, check or example
61ForceA push or pull that can change motion or deform an object.Show the direction and point of application on a sketch. Naming a force without locating it rarely explains the design problem.
62LoadA force or combination of forces applied to a structure or component.Include the stored objects as well as the product’s own weight when considering the loading of its support.
63TensionA pulling action that tends to stretch a component.A supporting cord may be in tension. Trace the force along the cord rather than judging only from its orientation.
64CompressionA pushing action that tends to shorten or crush a component.A supporting leg often carries compression. A slender member can buckle before the material is crushed.
65BendingDeformation that curves a member, commonly placing one side in tension and the other in compression.A loaded shelf may bend between supports. Changing its section or support arrangement can alter its response.
66TorsionA twisting action caused by a turning effect about a member’s length.A shaft transmitting a turning motion may experience torsion. Distinguish twisting from sideways bending.
67ShearLoading that tends to make adjacent parts of a material slide past one another.A fastener joining two sliding plates may experience shear. Mark the relevant sliding directions on a simple sketch.
68StabilityResistance to overturning or unwanted movement from an intended position.A wider support base can help against tipping, but check the direction of loading and where the combined weight acts.
69Centre of gravityThe point through which an object’s resultant weight can be considered to act.For simple tipping analysis, consider whether the vertical line through this point remains within the support base.
70BracingAdding members that resist unwanted deformation of a structure.A diagonal brace can resist a rectangular frame’s sideways distortion. Show how its connections allow it to do so.
61–70: Forces and structures

Motion and mechanical relationships

No.TermMeaningUse, check or example
71MotionMovement of a body or component, described by its path and direction.Describe the input movement and required output movement separately before choosing a mechanism.
72Linear motionMovement along a straight path.A guided sliding rack may move linearly. Its path matters more than whether it moves horizontally or vertically.
73Rotary motionMovement around an axis.A turning handle has rotary motion. Identify the axis and required direction in a mechanism sketch.
74Reciprocating motionRepeated movement backwards and forwards along a straight path.A sliding part that repeatedly moves out and returns reciprocates. A single movement outward is not the full repeating action.
75Oscillating motionRepeated angular movement backwards and forwards about a pivot.A rocking arm oscillates. Compare its curved path with the straight path of a reciprocating slider.
76LeverA member that turns about a pivot to transmit or modify a force and movement.Locate the input force, resisting load and pivot. A long-looking handle alone does not establish its mechanical advantage.
77FulcrumThe pivot about which a lever turns.Moving the fulcrum changes the lever arms. Explain how this affects the required force and movement in the example.
78Mechanical advantageThe ratio of useful output force to input force for a mechanism.An output force of 30 N from 10 N input gives a mechanical advantage of 3. It is a force ratio, not free energy.
79Gear trainTwo or more gears arranged to transmit rotary motion between shafts.Use tooth counts and connections to analyse speed and direction. Do not assume every gear in a train turns at the same speed.
80Rack and pinionA toothed straight rack meshing with a circular gear to convert rotary and linear motion.A rotating pinion can drive a rack along a straight path. Show where guides are needed to keep the parts aligned.
71–80: Motion and mechanical relationships

Mechanisms and control-system vocabulary

No.TermMeaningUse, check or example
81CamA shaped component whose movement produces a specified motion in a contacting follower.Its profile influences the follower’s movement. Explain how the particular shape creates the required output.
82FollowerThe component that moves in response to the surface of a cam.Identify how contact is maintained. Drawing a follower near a cam does not establish that it will follow the profile.
83LinkageConnected members arranged to transmit or change motion.Mark fixed pivots and moving joints. The motion depends on these connections, not just the outline of the bars.
84PulleyA wheel with a suitable rim or groove used with a belt or rope to transmit motion or redirect a force.A single fixed lifting pulley can change force direction without an ideal force advantage. Explain the actual arrangement.
85Screw mechanismA threaded arrangement that relates rotation to axial movement or force.A turning screw can advance a component. State which part is prevented from rotating freely in the intended arrangement.
86InputSomething entering a system, such as energy, a command or a measured signal.A button press may provide an input. Identify the particular system boundary before labelling a component.
87ProcessThe operation that transforms or responds to an input within a system.A controller may compare a measured value with a target. Describe that comparison instead of only writing “the system processes”.
88OutputThe result produced by a system.A motor’s movement may be an output. Distinguish the movement from a sensor reading sent back for control.
89FeedbackInformation about a system’s output or condition returned to influence its operation.A measured temperature can inform heater control. Feedback is not merely any information provided before the system starts.
90SensorA device that detects a physical condition and provides a corresponding signal.A light sensor detects illumination. Whether its reading forms feedback depends on how the rest of the system uses it.
81–90: Mechanisms and control-system vocabulary

Control, testing and justified conclusions

No.TermMeaningUse, check or example
91Open-loop controlControl that does not use feedback from the controlled output to adjust operation.A lamp operated only by a manual on/off command is a simple example. State the system you are analysing.
92Closed-loop controlControl that uses feedback about the controlled output to adjust operation towards a desired condition.A temperature controller compares a measured temperature with its target and changes heating accordingly.
93CircuitAn arrangement of connected electrical components through which current can flow when a conducting path is complete.Distinguish an open switch from a closed conducting path. Use approved low-voltage school equipment for practical work.
94ResistanceOpposition to electric current, measured in ohms.Do not confuse resistance, a quantity, with a resistor, a component. Relate the word to the circuit being discussed.
95ActuatorA component that converts a control signal and supplied energy into a physical action.A motor can act as an actuator by producing movement. A sensor generally detects a condition rather than doing this job.
96TestA planned activity used to obtain evidence about performance or a characteristic.State the conditions, measurement and success criterion. Asking whether someone likes the colour tests a different question from stability.
97EvaluationJudging a design using relevant criteria and evidence.Compare test results with the specification. Identify what is supported, what failed and what remains unknown.
98ReliabilityThe ability to perform the intended function consistently under specified conditions over a stated period.Repeat an appropriate test and record failures. One successful operation gives limited evidence about reliability.
99RefinementA purposeful change intended to improve a design in response to a reason or finding.Lower an obstructing edge after a retrieval test. Explain the result you expect and how you will check it.
100JustificationA reasoned explanation supporting a decision with relevant evidence and conditions.Explain why the chosen mechanism suits the required motion. Include a limitation instead of claiming it is best in every situation.
91–100: Control, testing and justified conclusions

Contents · Previous chapter · Next chapter

CHAPTER 3 OF 9

Common confusions that change a design answer

Back to contents

Strength, stiffness, hardness and toughness

Ask what is going wrong before choosing the property. If a support deflects too much under normal use, stiffness is directly relevant. If its surface is easily scratched, hardness may be relevant. If it fractures under a knock, toughness may matter. Strength concerns the stress a material can withstand without the specified form of failure. Several properties can matter in one product, but the terms are not interchangeable.

Also separate the material from the structure made with it. A thicker or differently shaped section can change the stiffness of a component even when the material stays the same. A comparison between two complete products therefore needs dimensions, shape and support conditions as well as the material name. Avoid concluding that one material is always better from a comparison that changed several features at once.

A specification, a test and an evaluation

A specification describes what the design should achieve. A test obtains evidence about its performance. An evaluation judges that evidence against the requirement. “The cards must remain accessible” is a starting requirement; it still needs a usable check. “Three users each retrieved a card without moving the holder in this trial” is an observation. “The arrangement met this trial’s retrieval requirement” is a limited judgement. None of these sentences should silently stand in for the other two.

A mock-up and a prototype

A quick cardboard mock-up may be the right tool for investigating opening size and hand clearance. Its speed and simplicity are advantages when the arrangement is still uncertain. A more developed prototype can investigate further aspects of function. Neither label automatically establishes quality. Say what the model was built to reveal, what it showed and which questions remain for another version.

A sensor and feedback

A system can contain a sensor without using feedback to control the output you are discussing. Suppose a temperature sensor merely displays a reading while a heater runs on a fixed timer. That measurement does not, by itself, adjust the heater. If a controller uses the measured temperature to change heating towards a target, it closes the relevant feedback loop. Identify the controlled quantity and trace how its measurement affects operation.

A neat sequence and an honest design process

The K345 design model allows revisiting earlier ideas as evidence changes. The Design Council’s Double Diamond offers another useful general explanation of exploring a problem, defining it, developing alternatives and testing solutions. Its description also recognises returning to earlier work. It is a design framework, not an extra SEAB examination requirement.

If a test reveals that the original requirement was incomplete, record the finding and reconsider it. A journal that explains a justified change can communicate stronger thinking than a smooth story in which the first idea appears perfect. The purpose of recording a process is to make the decisions understandable. Rewriting history to hide useful discoveries makes later evaluation harder.

Contents · Previous chapter · Next chapter

CHAPTER 4 OF 9

Five worked examples: from word to reasoned decision

Back to contents

All situations, measurements and results in this chapter are invented for teaching. They demonstrate how to reason with vocabulary and do not describe real Punggol users, product certifications or assessment results. Keep the conditions visible while following each explanation.

Worked example 1: a user need becomes a testable requirement

Imagine a student sorting revision cards on a narrow desk. The cards slide behind a pile of books, and the student moves the pile to retrieve them. The observation is the repeated retrieval difficulty. An appropriate design opportunity is improving access and organisation within the available space. “Build a wooden box” is already a proposed solution; it does not fully state the need.

A possible brief is: develop a desk-based holder that lets this student see and retrieve revision cards in the available area. For this invented exercise, the available footprint is 180 mm by 120 mm and the cards measure 100 mm by 70 mm. These measurements inform requirements, but they do not determine the entire design. The orientation, dividers and access opening still need investigation.

A useful check could ask the intended user to retrieve a specified card with one hand, without moving the holder or adjacent books. Decide the trial conditions first, observe what happens, and record difficulties. If the user can do it only when the holder is nearly empty, the design has not yet demonstrated access at its intended capacity. The vocabulary chain is need → constraint → specification → test → evaluation.

Change the condition: the desk footprint becomes smaller. You should revisit the arrangement and possibly the required capacity. Simply reducing every dimension may make the cards impossible to retrieve. The revised design must still answer the original user need.

Worked example 2: interpreting a fair material comparison

Two model shelves have identical dimensions and supports. In a teacher-planned trial, the same load is placed at the same position. Shelf A deflects 2 mm and Shelf B deflects 6 mm; neither fractures or remains bent after unloading. These are invented results. Under these conditions, A is the stiffer complete component because it deflects less for the same load.

The trial does not show which component has the higher failure strength, surface hardness or impact toughness. Those questions require different evidence. It also does not prove that A is the better choice overall: mass, cost, ease of manufacture and the allowable deflection may matter. A reasoned choice might say that A better meets a stated deflection requirement, while acknowledging that other requirements have not yet been compared.

Change the condition: Shelf A is twice as thick as Shelf B. You can still compare the tested components, but you can no longer attribute the difference solely to their materials. A fair investigation of material behaviour needs the geometry and other relevant conditions controlled.

Worked example 3: analysing a gear pair

A 12-tooth driver gear directly meshes with a 36-tooth driven gear on another shaft. In this idealised example, the driver turns at 90 revolutions per minute. The driven speed is 90 × 12 ÷ 36 = 30 revolutions per minute. For this simple pair of external gears, the driven gear rotates in the opposite direction.

The explanation should connect the tooth counts to the movement: each rotation of the smaller driver advances only one third of the teeth needed for a complete rotation of the larger gear. The arrangement reduces speed. In an ideal system, the corresponding torque increases, while real losses affect the actual result. It does not create energy or make every output force three times larger regardless of geometry.

Change the condition: the 36-tooth gear becomes the driver at 90 revolutions per minute. The 12-tooth driven gear now turns at 270 revolutions per minute. You must identify driver and driven before applying the relationship; memorising “divide by three” would produce the wrong answer.

Worked example 4: deciding whether control is closed-loop

System A switches a low-voltage model heater on for a fixed time. A separate display shows temperature but has no connection to the switching decision. System B measures temperature, compares it with a target and adjusts the heater using that comparison. These are conceptual school examples, not instructions for building a household heating device.

System A is open-loop with respect to controlling temperature because the temperature reading does not change the heating operation. System B uses closed-loop control: the measured condition returns as feedback and influences the output. In your explanation, name the input or measurement, the comparison in the process, the heating output and the route by which new measurements affect the next action.

Change the condition: the sensor in System B becomes disconnected. The controller can no longer use that measurement as intended. Do not assume the resulting behaviour; it depends on the controller’s design and fault handling. State the missing feedback and the resulting uncertainty.

Worked example 5: turning test evidence into a justified refinement

A card-holder mock-up is tested in its intended arrangement. In six observed retrieval attempts, the user catches a finger on the front edge four times. After lowering that edge, the same trial is repeated and the problem is not observed. This supports further consideration of the change for retrieval, but does not show that every user will find it comfortable or that the final material is durable.

A careful journal explanation identifies the feature, the evidence and the decision: the original edge obstructed access in the trial, so its height was reduced and the revised arrangement was retested. Then record any consequence. If the lower edge allows cards to fall out when moved, the refinement has introduced a trade-off. You may need another means of retaining cards or a clearer intended-use condition.

Change the condition: the holder must now be carried between rooms. A desk-only trial is no longer sufficient. Revisit retention, grip and loading during movement, and plan further appropriate checks with the teacher. A successful design decision remains tied to the conditions for which evidence was collected.

Contents · Previous chapter · Next chapter

CHAPTER 5 OF 9

Independent practice and explained answers

Back to contents

Attempt these questions before looking at the answers. Write enough to show the relationship between the words, not just a label. The questions are original learning checks, with no official marks or grade boundaries. Use a rough sketch where it makes your explanation clearer.

Question 1

A pupil writes: “My design must look attractive.” Explain why this is difficult to evaluate and suggest a more informative next step.

Question 2

A support bends noticeably under its normal load but returns to shape afterwards. Which property is directly relevant to limiting that deflection? What does the observation not prove?

Question 3

A drawing specifies a slot width of 42 ± 0.5 mm. Is a measured width of 42.7 mm within the stated tolerance? Explain.

Question 4

An 18-tooth gear drives a directly meshing 54-tooth external gear. The driver rotates at 120 revolutions per minute. Find the driven speed and describe its direction.

Question 5

A motor turns a circular gear that moves a toothed straight bar along guides. Name the mechanism and describe the motion conversion.

Question 6

A moisture sensor displays a reading, but a pump runs only according to a fixed timer. Does the displayed reading establish closed-loop moisture control?

Question 7

A cardboard mock-up permits comfortable hand access. A student concludes that the final acrylic product will withstand repeated drops. Evaluate the conclusion.

Question 8

A wider base makes a holder harder to tip, but it now extends beyond the permitted desk area. Explain the design problem and a sensible next action.

Answers and reasoning

Answer 1. The criterion is too vague to judge consistently. Identify the intended user and context, investigate the relevant visual preferences or communication needs, and specify what will be compared. Do not replace the vague claim with an arbitrary colour rule that has no evidence behind it.

Answer 2. Stiffness is directly relevant. The return towards the original shape indicates elastic behaviour under the tested conditions. The observation does not establish the maximum strength, impact toughness or long-term durability of the support.

Answer 3. No. The permitted interval is 41.5–42.5 mm, so 42.7 mm exceeds the upper limit by 0.2 mm. The stated tolerance belongs to this exercise; it is not a recommended allowance for every slot or manufacturing process.

Answer 4. The driven speed is 120 × 18 ÷ 54 = 40 revolutions per minute. With this direct pair of external gears, the driven gear turns in the opposite direction. The answer depends on the stated driver and arrangement.

Answer 5. It is a rack and pinion mechanism. The pinion’s rotary motion produces linear motion of the rack. The guides constrain the rack’s path; naming the mechanism alone does not explain the conversion.

Answer 6. No. The moisture reading is not used to adjust pumping in the stated arrangement. To establish closed-loop moisture control, explain how measured moisture is fed back and used to change operation towards the required condition.

Answer 7. The conclusion exceeds the evidence. The mock-up provides information about access in that arrangement, not the final material’s response to impact or repeated use. Identify the separate performance question and plan an appropriate teacher-supervised investigation.

Answer 8. This is a trade-off between stability and the footprint constraint. Keep both requirements visible and investigate alternatives, such as changing the arrangement or distribution of mass. Compare revised ideas against both conditions instead of declaring the wider base an unconditional improvement.

Use the result to choose one next action

A total score would hide useful information here. Look for the kind of error you made, repair that relationship, and then attempt a changed example without looking back. A correct answer that depends on copying is a useful first step, but it is not yet independent control.

What you noticeLikely gap to investigateSpecific practiceIndependent retest
Definitions sound similarStrength, stiffness, hardness and toughness are being mixed up.Sort four short failure descriptions by the most relevant property; explain why the other terms are less direct.Describe a new product problem and choose the relevant property with a reason.
The calculation changes unpredictablyDriver/driven or dimensional limits were not identified before calculation.Label the given values and state the relationship in words before substituting numbers.Reverse the gear roles or change the tolerance and recalculate from the new conditions.
A system label has no explanationSensor, input, output and feedback are being used as interchangeable labels.Draw the path from measurement through decision to action, then locate any return information.Classify a new system that measures a condition but does not use the reading to control it.
The conclusion is broader than the testA successful trial is being treated as proof of every required property.Write two lists: what the test supports and what it leaves unknown.Evaluate a different test where material, user or context changes.
A design improvement breaks another requirementOnly one criterion was considered when the change was judged.Compare the original and revised ideas against every relevant constraint.Explain a new trade-off and identify evidence needed before selecting an option.
Practice results: what to repair and how to check it again

Contents · Previous chapter · Next chapter

CHAPTER 6 OF 9

A manageable vocabulary revision routine

Back to contents

Build a small set around one actual difficulty

Select five to eight words connected to a recent question or design decision. For a bending support, your set might include load, stiffness, strength, material selection and evaluation. Keeping the words connected helps you explain an actual problem. Working through unrelated terms alphabetically can be useful for reference, but it does not automatically build a coherent answer.

For each word, write a short meaning, draw or describe an example and add one boundary: what does this word not establish? For stiffness, the boundary might be that limited deflection does not by itself establish impact toughness. This small extra question prevents an accurate definition from turning into an inaccurate conclusion.

Retrieve, compare and apply

Close the list and explain a word from memory. Check the explanation, correct the specific error, and try again later with a new example. Then compare two easily confused words in one sentence. Finally, apply them to a decision: “This test compared stiffness of these components; it did not measure their failure strength.” The routine is a suggested way to practise, not a promise of a particular examination result.

A short session can finish with a changed condition. Alter the material thickness, user, support position or required motion. Ask what remains true and what needs fresh evidence. This gives you a more useful check than reciting a memorised example whose answer you already know. If the condition changes your conclusion, explain why.

Keep a decision record that can be checked

Use four headings in your revision notebook: claim, evidence, limit and next action. For example, your claim may be that a wider opening improved access; the evidence is the observed retrieval trial; the limit is that only one user and one loading condition were tested; the next action is another appropriate check. This structure helps you recognise where an explanation is incomplete without writing pages of repeated definitions.

Return to a small selection after a gap and explain it without prompts. If you can retrieve meanings but still cannot apply them, spend the next session comparing cases. If you can reason aloud but your written answer is vague, practise one complete paragraph or labelled sketch. Match the practice to the problem that remains.

Contents · Previous chapter · Next chapter

CHAPTER 7 OF 9

How parents and teachers can help

Back to contents

Parents do not need to become technical specialists to support useful practice. Ask the student to show one decision and explain the problem it addresses. “What did you observe?” and “Which result made you change your mind?” invite reasoning. If the answer is uncertain, record the question for the teacher instead of turning it into a confrontation about effort.

Keep the distinction between helping and taking over clear. A parent can listen, help locate a source or ask a question. The student should make and explain their own design decisions and keep an honest record of the work. For an assessed project, follow the school’s current instructions about permitted support and supervision. Do not manufacture a polished project explanation that the student cannot defend.

The K345 project guidance describes a design journal and presentation board, with mock-ups and the resulting prototype submitted as part of the journal, and teachers acting as coursework supervisors. Its emphasis on a developing record matters: a journal is not simply a final advertisement for the finished object. Ask the school how the current requirements apply to the student’s work.

When extra explanation may help

Bring a specific example when asking for help: the original question, the student’s explanation, the misunderstood term and the attempted correction. This allows a teacher or tutor to distinguish a vocabulary gap from a deeper conceptual issue. “Help with D&T” is much harder to act on than “I confuse the evidence for stiffness with the evidence for strength”.

A small discussion group can use the same practice problem in different roles: one person proposes an explanation, one asks for the evidence and one changes a condition. Everyone should then answer a fresh question individually. Discussion is useful when it makes thinking visible; the final independent attempt shows whether each student can use the learning. This is an example learning activity, not a statement of current course availability.

Keep practical work within the right setting

The vocabulary examples here can be discussed, sketched and analysed without operating machinery. Actual workshop operations, heating, powered equipment and electrical construction require the school’s approved procedures, suitable equipment and supervision. A written explanation of a process does not replace practical instruction. When unsure about an operation, take the question to the supervising teacher.

Contents · Previous chapter · Next chapter

CHAPTER 8 OF 9

Questions students and parents often ask

Back to contents

Are these the official 100 words required by SEAB?

No. They are an editorial selection for teaching and revision. SEAB publishes the subject requirements; this teaching selection is not an official ranking. Use the linked official document and the teacher’s instructions for assessed scope; use this guide to improve explanations and identify gaps.

Must I use technical language in every sentence?

Use the precise term where it adds meaning, then explain the relevant relationship. A short accurate explanation is stronger than a sentence crowded with loosely connected terms. If a word can be removed without changing what you have explained, check whether it is doing useful work.

Is a longer design specification always better?

No. It should contain relevant requirements that guide decisions and can be evaluated appropriately. Repeating the same requirement in several forms does not make it more useful. Check whether each item follows from the user, context or genuine constraint.

Can I reuse a worked example in my project?

Use the reasoning method to understand a concept, but investigate your own design situation. The examples here use invented conditions and are not evidence about your user or product. Your project decisions need your own relevant observations, work and permitted support.

Should I memorise all the material names first?

Learn the names your current work requires, together with relevant properties and limitations. Then compare choices for a specific purpose. A long list of material names will not help much if you cannot explain why one property matters in the design situation.

What should I do when two answers both seem reasonable?

Compare their assumptions and evidence. Both may be defensible under different conditions, or one may leave out a constraint. State the conditions under which your choice works and what further information would help decide between the options.

Does a failed trial mean the whole design is a failure?

A trial can reveal a useful limit or a problem that needs correction. Record what happened, check whether the trial addressed the intended question, and plan a justified next step. Avoid hiding the result or claiming that one change has solved issues you have not checked.

Contents · Previous chapter · Next chapter

CHAPTER 9 OF 9

Official sources and where to continue

Back to contents

Curriculum and examination details were checked against the following sources for the 2027 course. The definitions, examples, questions and revision suggestions in this guide are original teaching explanations. They do not reproduce a set of official examination answers or guarantee coverage of every assessed detail.

Choose one question you could not answer independently, make the specific correction, and attempt a new version. Your next useful step is the one that lets you explain a design decision more accurately than you could before. Bring the remaining uncertainty to the teacher with the relevant sketch, wording or test result.

Contents · Previous chapter · Continue to the wider vocabulary reference

Continue from here: Start Here · Tuition · Education · Pathways · Parenting 101 · All Site Routes

eduKate Punggol

Contact

83 Punggol Central, Singapore 828761

edu|Kate Bukit Timah

8 Fourth Avenue, Singapore 268674

By Appointment +65 8823 1234
admin@edukatesg.com

Email Us

When a child finally understands, school becomes less frightening and the future opens wider. Email us for the latest schedules and fees.

← 返回

感谢您的回复。 ✨