This Top 100 Secondary 2 G3 Vocabulary List for Punggol focuses on Science: forces, energy, heat and electricity. It helps students distinguish mass from weight, explain how energy moves between objects, read a circuit diagram and connect a calculation to the quantity being measured. Each term has a clear meaning and an original example. The worked sections then show how the vocabulary supports complete answers, from explaining a warm surface to comparing electrical energy consumption under stated conditions.
For parents, begin with the sentence that caused the difficulty. “The current is used up”, “heat always rises” and “a stationary object has no forces” reveal different misunderstandings. This guide shows how to repair those ideas with a diagram, a comparison or a short calculation. The 100 entries are eduKate’s teaching selection, not an official MOE or SEAB word list or an examination prediction. Use the student’s school topic outline to decide which group matters now and which earlier ideas need refreshing.
- For: Secondary 2 students studying G3 Science, and Punggol parents supporting their learning.
- Inside: exactly 100 selected terms in ten groups, with meanings and original examples.
- Key distinctions: force and pressure; mass and weight; heat and temperature; current and energy.
- Practice: worked explanations, clearly labelled fictional data and a diagnostic with answers.
- Calculation habit: name the quantity, check the conditions, use compatible units and interpret the result.
- Curriculum boundary: follow school assessment instructions; this is lower-secondary learning, not a later national SEC paper.
- Practical work: circuit examples refer to teacher-supervised low-voltage equipment; home electrical alterations are not learning activities.
Contents
Understand the scope and find the vocabulary
Apply the vocabulary in learning
- Distinguish mass, weight, force and pressure
- Calculate work only after checking the force and movement
- Explain heat transfer without treating heat as a substance
- Track current and energy separately in a circuit
- Keep power, time, energy and cost in different places
- Analyse fictional cooling data before claiming a cause
- Try eight questions, then check the reasoning
- Build a routine around one connected idea
Parents, questions and official references
Jump to a ten-word group
- Words 1–10: Forces, mass and weight
- Words 11–20: Effects of forces
- Words 21–30: Work and energy
- Words 31–40: Sources of energy
- Words 41–50: Temperature and thermal effects
- Words 51–60: Heat transfer
- Words 61–70: Electrical quantities
- Words 71–80: Components and arrangements
- Words 81–90: Circuit behaviour and power
- Words 91–100: Calculations and investigation
The MOE G2/G3 Lower Secondary Science syllabus includes forces and energy transfer, heat transfer and electrical systems. It covers pressure, work, energy conservation, current, potential difference, resistance, power and electricity-consumption costs. Its Electrical Systems section explicitly states that the formula V = IR is not required. This guide therefore develops those meanings without treating Ohm’s-law calculations as compulsory lower-secondary work.
Official school resources provide another useful check. The Yusof Ishak Science learning index places these topics within its Secondary 2 resources, and Yishun Secondary publishes level-specific Science outlines. These are examples of school communication, not a universal weekly sequence. Ask your child’s school which topics and question types are currently being assessed.
Some vocabulary below names units, apparatus or actions needed to explain the subject. Inclusion does not mean every term is a separately prescribed syllabus outcome. Read each worked example’s conditions carefully. A simplified calculation can be useful without becoming a rule that applies to every real device or moving object.
CHAPTER 2 OF 13 · Find the vocabulary
2. 100 vocabulary terms for forces, energy, heat and electricity
The numbers organise revision rather than rank examination frequency. For each group, ask the student to explain one example, identify a near miss and use the term in a fresh situation. A scientific word becomes useful when it helps the student decide what the evidence means.
Words 1–10: Forces, mass and weight
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 1 | Force | A push or pull arising from an interaction. | A hand changes a sponge’s shape by applying a force. |
| 2 | Contact force | A force acting where objects or materials are in contact. | A shelf exerts an upward contact force on a resting box. |
| 3 | Non-contact force | A force that can act without the interacting objects touching. | Earth attracts a falling object before it reaches the ground. |
| 4 | Friction | A contact force opposing relative sliding or its tendency between surfaces. | Friction helps a pencil grip prevent the pencil slipping through fingers. |
| 5 | Gravitational force | The attractive interaction between objects with mass. | Earth’s gravitational force contributes to a book’s weight. |
| 6 | Magnetic force | A force associated with magnets, magnetic fields and suitable materials. | Two magnets can attract or repel depending on their orientation. |
| 7 | Elastic force | A restoring force produced when an elastic object is deformed. | A stretched spring pulls towards its original length. |
| 8 | Mass | A measure of the amount of matter in an object. | A model specifies a trolley’s mass as 0.8 kg. |
| 9 | Weight | The gravitational force acting on an object. | Using the stated approximation g = 10 N/kg, a 0.8 kg trolley weighs 8 N. |
| 10 | Newton | The SI unit of force, written N. | A force-meter reading of 3 N describes force rather than mass. |
Words 11–20: Effects of forces
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 11 | Balanced forces | Forces on one object that combine to give zero overall force. | A stationary book can have its weight balanced by an upward support force. |
| 12 | Unbalanced forces | Forces combining to give a non-zero overall force. | An unbalanced force can change an object’s speed or direction. |
| 13 | Motion | A change in position relative to a chosen reference. | A trolley moves relative to the laboratory bench beside it. |
| 14 | Speed | Distance travelled per unit time. | A model trolley travelling 6 m in 3 s has average speed 2 m/s. |
| 15 | Direction | The way in which a force acts or an object moves. | A force arrow must indicate both the object affected and the direction of action. |
| 16 | Turning effect | The tendency of a force to rotate an object about a point or axis. | A push on a door can turn it about its hinges. |
| 17 | Pivot | A point or support about which an object can turn. | A balanced seesaw can rotate about its central pivot. |
| 18 | Lever | A rigid object that turns about a pivot to transmit a force. | A simple classroom lever transfers a student’s effort to a load. |
| 19 | Pressure | Force acting normally on a surface divided by its area. | The same load produces greater average pressure over a smaller contact area. |
| 20 | Contact area | The surface area over which objects touch and a force acts. | A wider bag strap can spread a supporting force over a larger area. |
Words 21–30: Work and energy
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 21 | Work done | Energy transferred by a force acting through a displacement. | A constant 12 N force acting along a 3 m movement does 36 J of work. |
| 22 | Energy | A conserved quantity transferred when systems interact or change. | An energy account includes changes in the object and its surroundings. |
| 23 | Energy transfer | Movement of energy from one object or system to another. | A moving hand transfers energy when it pushes a trolley. |
| 24 | Energy conversion | A change from one form of energy to another. | A small electric motor converts electrical energy into motion and other outputs. |
| 25 | Conservation of energy | Energy is not created or destroyed during transfers and conversions. | A slowing toy can transfer energy to its surroundings rather than lose energy from existence. |
| 26 | Kinetic energy | Energy associated with an object’s motion. | A rolling marble has kinetic energy because it is moving. |
| 27 | Gravitational potential energy | Energy associated with position in a gravitational field. | Lifting a book raises its gravitational potential energy relative to the table. |
| 28 | Elastic potential energy | Energy stored through elastic deformation. | A gently compressed spring can store elastic potential energy. |
| 29 | Chemical energy | Energy associated with substances’ chemical arrangements. | An electrochemical cell transfers energy through chemical changes within it. |
| 30 | Joule | The SI unit of energy and work, written J. | An answer of 36 J describes transferred energy, not the size of a force. |
Words 31–40: Sources of energy
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 31 | Energy source | A resource from which usable energy can be obtained. | A worksheet compares sunlight and fuel as sources for different systems. |
| 32 | Fossil fuel | A fuel formed over geological time from ancient organic material. | Coal, oil and natural gas are familiar fossil-fuel examples. |
| 33 | Renewable | Describing a resource replenished naturally on useful human timescales. | Wind is renewable, although its availability varies over time. |
| 34 | Non-renewable | Describing a resource not replenished quickly enough to match human use. | A fuel deposit can be depleted much faster than it forms naturally. |
| 35 | Solar energy | Energy received from the Sun’s radiation. | A solar cell can convert some incoming radiation into electrical energy. |
| 36 | Wind energy | Energy obtained from moving air. | Moving air turns a turbine that is connected to a generator. |
| 37 | Hydroelectric energy | Electrical energy generated using moving water. | Water flowing through turbines can drive generators in a hydroelectric system. |
| 38 | Geothermal energy | Energy obtained from Earth’s internal heat. | A diagram identifies underground heat as the source in a geothermal system. |
| 39 | Biofuel | A fuel made from recently living biological material. | A comparison considers fuel made from plant material and the resources needed to produce it. |
| 40 | Nuclear energy | Energy released through changes involving atomic nuclei. | A source comparison distinguishes nuclear processes from ordinary fuel combustion. |
Words 41–50: Temperature and thermal effects
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 41 | Heat | Energy transferred because of a temperature difference. | Energy transfers from a warmer object to cooler surroundings as heat. |
| 42 | Temperature | A measure of how hot or cold an object or substance is. | A thermometer reading does not by itself reveal the sample’s total stored energy. |
| 43 | Thermometer | An instrument used to measure temperature. | A temperature probe supplies readings for a fictional cooling graph. |
| 44 | Kelvin | The SI unit of thermodynamic temperature, written K. | Use K, without a degree symbol, when a temperature is expressed in kelvin. |
| 45 | Celsius | A commonly used temperature scale, written with the symbol °C. | A classroom result states the water temperature as 35°C. |
| 46 | Thermal expansion | An increase in a material’s dimensions associated with heating. | A suitable liquid expands when warmed, while its individual particles do not grow larger. |
| 47 | Thermal contraction | A decrease in a material’s dimensions associated with cooling. | A metal rod usually becomes slightly shorter as it cools. |
| 48 | Volume | The amount of space occupied by an object or sample. | A fictional liquid sample increases from 100 cm³ to 102 cm³ on warming. |
| 49 | Density | Mass per unit volume. | If the same mass occupies a larger volume, its average density decreases. |
| 50 | Fluid | A substance that can flow, including liquids and gases. | Both water and air can participate in convection. |
Words 51–60: Heat transfer
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 51 | Conduction | Energy transfer through a material without bulk movement of that material. | A metal tray can conduct energy from its warmer region towards a cooler region. |
| 52 | Convection | Energy transfer involving the bulk movement of a fluid. | Circulating water carries energy between regions of a container. |
| 53 | Radiation | Energy transfer by electromagnetic waves, which can travel through a vacuum. | Radiation can carry energy across an evacuated gap. |
| 54 | Thermal conductor | A material through which energy transfers relatively readily by conduction. | A metal cooking surface is chosen partly for its thermal conduction. |
| 55 | Thermal insulator | A material that reduces the rate of energy transfer by conduction. | A suitable handle material slows energy transfer towards the user’s hand. |
| 56 | Convection current | A circulating flow produced by density differences in a fluid under gravity. | Warmer, less dense fluid can rise as cooler fluid moves into its place. |
| 57 | Infrared | Electromagnetic radiation strongly associated with thermal emission at everyday temperatures. | A thermal camera detects infrared radiation rather than measuring visible brightness alone. |
| 58 | Absorption | Taking in energy from incoming radiation. | Energy absorbed from radiation can increase an object’s internal energy. |
| 59 | Emission | The release of radiation from a source or surface. | A warm surface emits thermal radiation even when it does not visibly glow. |
| 60 | Reflection | Radiation returning from a surface rather than being absorbed or transmitted. | A suitable shiny surface can reflect much of the incident thermal radiation. |
Words 61–70: Electrical quantities
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 61 | Electric charge | A property of matter associated with electrical interactions. | Moving charges in a circuit are not the same thing as the energy being transferred. |
| 62 | Current | The rate at which electric charge passes a point. | Steady current in a simple series loop is the same before and after a lamp. |
| 63 | Ampere | The SI unit of electric current, written A. | A reading of 0.25 A reports current rather than potential difference. |
| 64 | Potential difference | Energy transferred per unit charge between two points. | A potential difference is measured across a component, not at one isolated point. |
| 65 | Volt | The unit of potential difference, written V. | A labelled classroom supply has a potential difference of 3 V. |
| 66 | Resistance | A measure of opposition to the flow of electric current. | At the same supplied potential difference, a higher-resistance path carries less current. |
| 67 | Ohm | The unit of electrical resistance, written Ω. | A resistor marked 20 Ω is labelled by resistance, not by power. |
| 68 | Electrical conductor | A material that allows electric charge to move through it readily. | A metal wire provides a conducting path in a classroom circuit. |
| 69 | Electrical insulator | A material that strongly restricts charge movement under ordinary conditions. | A wire’s suitable plastic covering helps separate its conductor from nearby objects. |
| 70 | Circuit | An arrangement of connected electrical components and paths. | A circuit diagram represents connections rather than the physical appearance of the equipment. |
Words 71–80: Components and arrangements
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 71 | Cell | A single electrochemical unit that can supply electrical energy. | One long-short line pair represents a cell in a standard school circuit diagram. |
| 72 | Battery | In school circuit symbols, a supply represented by two or more connected cells. | Repeated long-short line pairs distinguish the drawn battery symbol from a single cell. |
| 73 | Switch | A component used to open or close a conducting path. | An open switch interrupts the intended path in a simple circuit. |
| 74 | Lamp | A component designed to convert supplied energy into light, with other outputs too. | A filament lamp also transfers substantial energy as heating. |
| 75 | Resistor | A component providing resistance in an electrical circuit. | A circuit diagram uses a resistor symbol instead of a drawing of its casing. |
| 76 | Variable resistor | A resistor whose resistance can be adjusted. | A supervised investigation changes its setting while monitoring the circuit current. |
| 77 | Ammeter | An instrument that measures current and is placed in series with the measured path. | A diagram places the ammeter within the branch whose current is needed. |
| 78 | Voltmeter | An instrument measuring potential difference between two points. | A diagram connects the voltmeter across the lamp being investigated. |
| 79 | Series circuit | A circuit arrangement with components along one unbranched current path. | Two lamps in a simple series loop share the same steady current. |
| 80 | Parallel circuit | An arrangement with separate branches connected across the same two junctions. | The potential difference across those parallel branches is the same. |
Words 81–90: Circuit behaviour and power
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 81 | Closed circuit | A circuit with a complete conducting path for current. | Closing the intended switch can complete a teacher-approved low-voltage circuit. |
| 82 | Open circuit | A circuit with a break interrupting the conducting path. | A break in a simple series loop prevents current throughout that loop. |
| 83 | Branch | A separate path within a circuit containing junctions. | One parallel branch can contain a lamp while another contains a resistor. |
| 84 | Junction | A point where current paths meet or divide. | At steady state, the total current entering a junction equals the total leaving. |
| 85 | Short circuit | An unintended low-resistance path that can allow excessive current. | A worksheet identifies a bypassed component as a circuit fault requiring safe correction. |
| 86 | Overloading | Drawing more current than the circuit or equipment is designed to carry safely. | An overloaded system can overheat; it is not a situation to reproduce for practice. |
| 87 | Fuse | A protective component designed to melt and break a circuit when excessive current flows. | A circuit explanation describes the fuse interrupting the faulty current path. |
| 88 | Power | The rate at which energy is transferred or converted. | A model device transferring 90 J in 3 s has average power 30 W. |
| 89 | Watt | The unit of power equal to one joule transferred per second. | A constant power of 20 W corresponds to 20 J transferred each second. |
| 90 | Kilowatt-hour | The energy transferred at a power of one kilowatt for one hour. | A 0.5 kW device operating steadily for 2 h uses 1 kWh. |
Words 91–100: Calculations and investigation
| No. | Term | Meaning | Original example |
|---|---|---|---|
| 91 | Kilowatt | A unit of power equal to 1,000 watts. | A labelled power of 600 W is equivalent to 0.6 kW. |
| 92 | Energy consumption | The amount of energy used by a device or system over a period. | Compare both operating power and duration when estimating consumption. |
| 93 | Tariff | A stated charging rate, such as a price per kilowatt-hour. | A fictional tariff of $0.30 per kWh is supplied for a calculation. |
| 94 | Independent variable | The factor deliberately changed to investigate its effect. | A cooling comparison changes only the specified insulating sleeve material. |
| 95 | Dependent variable | The response measured during an investigation. | The measured temperature drop after five minutes is the dependent variable. |
| 96 | Controlled variable | A relevant factor kept constant for a meaningful comparison. | The two cooling samples begin with the same water mass and initial temperature. |
| 97 | Trend | A general pattern shown by a set of results. | A graph may show temperature decreasing more slowly as it approaches room temperature. |
| 98 | Anomaly | A result that differs noticeably from the surrounding pattern. | An unexpected temperature rise during a cooling run prompts a check of the procedure. |
| 99 | Predict | State an expected result using evidence or a scientific model. | Predict a change in pressure while keeping the applied force constant. |
| 100 | Explain | Link an observation to a scientific reason or mechanism. | Explain cooling by identifying the direction and processes of energy transfer. |
CHAPTER 3 OF 13 · Understand and learn
3. Distinguish mass, weight, force and pressure
A student writes, “The box has a weight of 2 kg.” The number may be familiar, but the unit reveals a confusion. Kilograms measure mass. Newtons measure force, including weight. For an illustrative classroom calculation, take gravitational field strength g = 10 N/kg. A mass of 2 kg then has weight 2 × 10 = 20 N. This is a stated approximation; use the value given in the actual question.
A stationary box on a level table can still experience forces. Its downward weight is balanced by an upward supporting force. Stationary does not mean force-free. Draw both arrows on the box and name their sources. Avoid placing one arrow on the box and another on the table, then treating them as balanced forces on the same object.
Pressure asks a different question: how concentrated is a force over an area? Suppose a fictional support exerts a normal force of 30 N over 0.015 m². Its average pressure is 30 ÷ 0.015 = 2,000 N/m², or 2,000 Pa. If the same force acts over twice the area, the average pressure halves. It is the force per area that changes, not necessarily the total force.
In a turning question, identify the pivot and the force direction. Pushing a door farther from its hinges generally makes turning easier when the other conditions, including how the push acts, are comparable. The task here is to explain the relationship. There is no need to import an advanced rotational equation unless it belongs to the lesson being taught.
CHAPTER 4 OF 13 · Understand and learn
4. Calculate work only after checking the force and movement
In a simple example, a constant horizontal force of 15 N acts on a trolley while it moves 4 m in that same direction. Work done by that force is force × distance moved in the force’s direction: 15 × 4 = 60 J. Both conditions matter: the force is constant and its direction matches the displacement. The calculation describes the work of that particular force.
If friction also acts, it does not follow that the trolley gains 60 J of kinetic energy. Some energy can transfer to the surroundings, and the total change depends on all relevant interactions. A student should not turn one force’s work into a claim about the whole energy account without considering the rest of the situation.
Holding a bag motionless can feel tiring. Yet the upward supporting force does no mechanical work on the stationary bag through displacement because the bag does not move. The person’s body still uses energy internally. The apparent contradiction disappears when the answer distinguishes everyday effort from the particular mechanical work being calculated.
Energy language should also retain the destination. A slowing object does not destroy its energy. Energy may transfer into heating of the object and surroundings, sound or other changes. Ask the student to extend an explanation beyond “energy is lost”: lost from which object, transferred by what interaction, and received where?
When comparing energy sources, distinguish a resource from an energy form. Wind is a source involving moving air; kinetic energy describes an associated form. Renewable does not mean continuously available or free of environmental effects. A sound comparison considers the stated purpose, availability and relevant impacts rather than treating one label as a complete judgement.
CHAPTER 5 OF 13 · Understand and learn
5. Explain heat transfer without treating heat as a substance
Heat describes energy transfer driven by a temperature difference. It is not a material fluid stored in objects. Temperature describes how hot or cold something is; it does not by itself specify the total energy of a sample. A small and a large quantity of water can have the same temperature while involving different amounts of matter.
For conduction, describe energy moving through the material without the material flowing bodily from one end to the other. A metal strip does not have to pour along itself for its cooler end to warm. A particle explanation can discuss interactions transferring energy between neighbouring regions. Saying “the hot particles travel all the way to the cold end” confuses conduction with bulk fluid movement.
For convection, movement of the fluid is central. A warmer region of a suitable liquid usually expands, becomes less dense and rises within cooler, denser liquid under gravity. Other fluid moves into its place, creating circulation. “Heat rises” omits the substance, the density change and the reason for movement. It also fails to describe conduction or radiation.
Radiation does not require matter between source and receiver. An evacuated gap can therefore reduce conduction and prevent ordinary convection across it while still allowing radiation. Suitable reflective surfaces reduce absorption of incoming radiation. Under comparable conditions, surface properties and temperature affect radiation transfer; do not assume colour alone settles every real-world heating problem.
A thermal insulator slows a transfer process. It does not necessarily stop all energy transfer or create warmth. Ask which pathways the proposed insulation affects: conduction through a material, fluid circulation around it, radiation between surfaces, or several together. This question turns a list of mechanisms into a useful explanation of a design.
CHAPTER 6 OF 13 · Understand and learn
6. Track current and energy separately in a circuit
Start with the connections rather than the drawing’s shape. A circuit drawn as a rectangle and the same circuit drawn as an irregular loop can represent identical connections. Trace each unbroken path. A crossover without an indicated connection does not automatically create a junction; follow the conventions used in the diagram.
In a simple steady series circuit, current is the same through components along the single path. A lamp does not use up current so that less returns to the source. Energy is transferred as charges pass through the system. That is why current and potential difference are different quantities and why their instruments are used differently.
On a correct teacher-provided diagram, an ammeter sits in series within the path being measured. A voltmeter measures between two points, across the component of interest. Students can check these positions on paper. Any practical investigation should use the teacher’s approved low-voltage supply and equipment, with the teacher supervising changes.
In parallel branches connected across the same two junctions, the potential difference is the same. Current divides between branches and combines again. If the branches differ, their currents need not be equal. At steady state, total current entering a junction equals total current leaving it. The junction does not create or consume charge.
Comparisons require conditions. Adding a parallel resistive branch to a source that maintains the same potential difference increases the total current demanded. Replacing one resistor with a higher-resistance component at the same supplied potential difference reduces its current. These qualitative relationships support understanding; this guide does not require using V = IR to calculate them.
CHAPTER 7 OF 13 · Understand and learn
7. Keep power, time, energy and cost in different places
Power is a rate. Energy consumption accumulates over time. A high-power device used briefly can consume less energy than a lower-power device used much longer. To compare fairly, state the operating duration and whether the quoted power is maintained throughout the example.
Fictional calculation: device A operates steadily at 600 W for 30 minutes. Convert 600 W to 0.6 kW and 30 minutes to 0.5 h. Its consumption is 0.6 × 0.5 = 0.30 kWh. At an invented tariff of $0.30 per kWh, the energy charge is $0.09. This is a teaching rate, not a current Singapore electricity tariff.
Device B operates steadily at 200 W for two hours. Its consumption is 0.2 × 2 = 0.40 kWh, so its corresponding charge is $0.12 at that same fictional rate. B has lower power but greater consumption over the periods compared. Comparing the wattages alone would give an incomplete answer.
Real appliances may cycle on and off or operate at changing power. The simple multiplication assumes constant power or an appropriate average. A real bill may also contain other charges. The model helps students learn the quantities and units; it should not be presented as a complete household bill calculation.
CHAPTER 8 OF 13 · Understand and learn
8. Analyse fictional cooling data before claiming a cause
Imagine two identical containers holding equal masses of water, each initially at 70°C. They have identical lids and are in the same room. The only planned difference is the insulating sleeve. After five minutes, sample A is at 61°C and sample B at 65°C. These are invented values for comparing evidence.
A’s temperature drop is 9°C; B’s is 5°C. Their average cooling rates over this interval are 1.8°C per minute and 1.0°C per minute respectively. This supports the statement that B cooled more slowly during this test. It does not mean either sample will continue cooling at that same rate indefinitely.
The sleeve material is the independent variable; temperature drop after the fixed time is the dependent variable. Relevant controls include water mass, initial temperature, container dimensions, lids and surroundings. Repeating the comparison would help assess consistency. If one container began with more water, the conclusion about sleeve material would be less secure.
Do not claim the data directly measure energy in joules or prove that only conduction occurred. Several pathways can contribute to cooling. At this level, identify the measured pattern, propose the relevant mechanism and state what would need checking. A careful answer can be useful without pretending the evidence settles every possible explanation.
CHAPTER 9 OF 13 · Understand and learn
9. Try eight questions, then check the reasoning
Complete these original teaching checks without looking at the tables. State units and conditions where needed; this activity is not a school grading or placement test.
- Using the given approximation g = 10 N/kg, find the weight of a 600 g object.
- A normal force of 24 N acts over 0.012 m². Calculate the average pressure.
- A constant 8 N force acts along a 2.5 m displacement. Find the work done by that force.
- A student writes, “Metal particles flow along the rod during conduction.” Repair the explanation.
- Why is “the lamp uses up current” incorrect for a simple steady series circuit?
- A junction receives 0.60 A and has two outgoing branch currents. One is 0.25 A. Find the other.
- A hypothetical device uses constant power 400 W for 45 minutes. Find its energy consumption in kWh.
- Two cooling samples start at different temperatures. Why might that weaken a comparison of their insulating materials?
Answers and the distinction each one checks
- 6 N. Convert 600 g to 0.6 kg, then calculate 0.6 × 10. The unit is newtons because weight is a force.
- 2,000 Pa. Pressure = 24 ÷ 0.012 = 2,000 N/m². The stated force acts normally over the stated area.
- 20 J. Work done = 8 × 2.5. The simple multiplication applies because the force is constant and acts along the displacement.
- Energy transfers without bulk movement of the rod material. Particle interactions help transfer energy; the rod does not flow from the warmer end to the cooler end.
- The same steady current passes through the series path. The lamp transfers energy into other forms; it does not consume the moving charge.
- 0.35 A. The outgoing currents must total 0.60 A at steady state, so subtract 0.25 A from 0.60 A.
- 0.30 kWh. Convert to 0.4 kW and 0.75 h, then multiply. A kilowatt-hour measures energy, not power.
- Initial temperature is a relevant control. Different temperature differences from the surroundings can affect cooling, making the sleeve comparison harder to interpret.
When an answer is wrong, locate the earliest failure: term meaning, condition, unit conversion, calculation or explanation. Then change one feature and try again. A correct copied correction is a starting point; independent use in a new example is the stronger check.
CHAPTER 10 OF 13 · Understand and learn
10. Build a routine around one connected idea
Select four or five terms from the current school topic. For a forces lesson, a useful set might be mass, weight, newton, force and pressure. Explain their differences, complete one calculation and draw one diagram. Avoid combining unrelated terms merely because they sit on the same revision page.
On a later day, ask for the explanation without showing the original example. Change a mass from kilograms to grams, rotate a circuit drawing or alter which quantity is held constant. Small changes reveal whether the student recognises the relationship or only remembers the earlier numbers.
Use a correction record with three short parts: the mistaken claim, the repaired idea and a new example. “Current is used up” can become “energy is transferred while charge circulates”, followed by a correctly labelled series diagram. This makes the progress specific enough to discuss with a teacher or tutor.
In an illustrative three-student lesson, each learner first answers independently. One then explains the quantities, another checks the conditions and the third checks the evidence or units. Rotate roles and finish with separate questions. A confident group explanation is valuable, but the final individual check shows what each student can actually do.
CHAPTER 11 OF 13 · Support and reference
11. Choose support using evidence from schoolwork
If a student confuses everyday and scientific meanings, start with contrasts. Work does not simply mean effort; power is not energy; a bigger force does not automatically mean a bigger pressure if area changes too. A short explanation with two carefully chosen examples can address the problem more directly than a long worksheet.
If the concepts are clear but calculations fail, inspect units and conditions. Does the student convert minutes to hours before using kilowatts? Do they know whether a force acts along the movement? Can they distinguish an average rate from a rate that remains constant? These questions identify a teachable next step.
If the student is progressing well, ask for a limitation. What assumption allows the electricity-cost calculation? Why does one cooling experiment not prove a mechanism by itself? Could a stationary object still experience forces? Deeper reasoning can grow within the current topic without adding unnecessary upper-secondary equations.
When considering small groups tuition in Punggol, bring a marked response and the current topic outline. Ask how each student’s understanding will be checked, how practical examples will be handled and what follow-up work is appropriate. Confirm actual class arrangements directly. This guide describes learning needs rather than establishing fees, schedules or availability.
Must every term be memorised before attempting questions?
No. Learn a connected set, then use it. A question helps reveal which definition needs more attention. Treat the full list as a reference for repeated visits rather than a one-evening memory target.
Can a student say that energy is wasted?
Yes, if they explain the intended purpose. Energy transferred into unwanted heating may be wasted for that device’s purpose, but it has not been destroyed. Identify where it goes.
Why do some questions use 10 N/kg?
It is a convenient classroom approximation for gravitational field strength near Earth’s surface. Use the value supplied by the teacher or question. Keep N/kg distinct from kilograms and newtons.
Is electricity always safer because the example uses a cell?
A small source can still cause problems if misused. Learn connections using diagrams and teacher-approved low-voltage equipment under supervision. Do not create short circuits or overloads to test an explanation.
Does a material insulate against everything?
No. Specify the process. Thermal insulation concerns energy transfer; electrical insulation concerns charge movement. A design may need both, and each property must be considered in its own context.
Reviewed on 16 November 2026. Official sources establish curriculum context. The vocabulary selection, worked examples, fictional data and lesson suggestions are original teaching material. Use the school’s latest instructions for immediate assessment preparation.
- MOE G2/G3 Lower Secondary Science syllabus, updated April 2024.
- Yusof Ishak Science: Secondary 1 and 2 G2/G3 learning resources.
- Yishun Secondary School: Science content outlines.
- AES Lower Secondary Science: Forces and Transfer of Energy.
- AES Lower Secondary Science: Transfer of Heat Energy.
- AES Lower Secondary Science: Electrical Systems.
Continue with the Secondary 2 G3 Science vocabulary guide for a wider view of the subject and questions to discuss when arranging support.

