For Punggol students taking SEC G1 Science, Machines Around Us (II) brings together energy, electricity, waves and the effects of forces. In the published 2027 K123 syllabus, students explain everyday systems and use relationships for power, electrical power, average speed and acceleration. Check the subject level and examination year confirmed by your school before choosing a revision resource.
Start each problem by naming the quantity you need, choosing the information that belongs to it and predicting what a reasonable answer would look like. This workbook gives you original practice cases, worked calculations and corrections. Use the cases alongside the topics your teacher has taught, then try the changed questions to see whether you can use the idea independently.
- Confirm that you are studying G1 Science and find the syllabus for your own examination year.
- Keep energy, power, current, voltage, speed and acceleration on separate lines when reading a problem.
- Convert minutes to seconds for calculations in joules and watts, and use hours when calculating electrical energy in kilowatt-hours.
- Read a circuit as connected paths. Follow the branches before deciding where currents or voltages belong.
- Describe a wave using evidence about its height, spacing or repetitions, then choose the appropriate scientific term.
- Explain a force through the change it produces, and interpret the whole journey before calculating average speed.
- Use the answer discussions after an attempt, then retry with the changed values or conditions.
On this page
Find the examination and the part you are practising · Build an energy account for a system · Use power to compare the rate of transfer · Calculate electrical energy and a fictional cost · Read series circuits by following one complete path · Follow the branches in a parallel circuit · Connect voltage and current to electrical power · Explain generation and transmission as a sequence · Read waves using one feature at a time · Match a wave application to the information supplied · Describe what a force changes · Calculate a whole journey before dividing · Read acceleration and distance-time graphs · Combine the ideas in a fictional display investigation · Use a short practice paper to identify the next repair · Make corrections show the decision you changed
Find the examination and the part you are practising
A Posting Group describes the route used for admission to secondary school. G1 Science identifies a particular subject level. A pupil admitted through PG1 might take Science at another level through the school’s subject arrangements, so begin with the actual subject confirmation. This workbook is designed around the upper-secondary Machines Around Us (II) section of G1 Science. Your Secondary 1 Science lessons have their own curriculum and teaching sequence. If you are still in lower secondary, let your teacher identify which examples fit the current work.
The official 2027 G1 Science K123 syllabus describes a 75-minute e-examination and a 60-minute second paper, each carrying 50 marks and half of the subject result. All questions in both papers are compulsory. The second paper includes a data-response question. A question on energy or electricity can therefore ask you to interpret unfamiliar information as well as recall a fact. The practice below uses invented figures so that you can make and check those decisions yourself.
For your own sitting, locate the appropriate document through the school-candidate syllabus index. Look for the subject name, level and examination year on the cover. A student beginning Secondary 1 in 2027 will sit a later examination. Reading the 2027 document can show that student how an examination syllabus is organised, while the school’s current lessons guide immediate preparation.
Keep a short record beside your practice. Write the date, the concept, the first answer and the correction you will test next. For example, “I used minutes with watts, then changed the time to seconds” is a clear record of a repair. When a later question gives hours, pause and choose the unit system again. Successful practice means you can recognise the decision when the surface details change.
The other K123 sections concern food and the body and health. This workbook covers one part of the course. A revision plan should return to the full subject when planning for either paper. Ask your teacher which areas are due next, how to access the school’s digital practice and which recent work best shows your understanding. The Punggol guide to G1, G2 and G3 subject offers explains how to discuss a student’s confirmed combination.
Build an energy account for a system
Imagine a small battery-operated model vehicle prepared for a classroom display. The battery stores chemical energy. When the switch is closed, electrical energy is transferred through the circuit. The motor turns the wheels, and the moving vehicle has kinetic energy. The motor and wheels also transfer energy to the surroundings through heating and sound. A good explanation follows the named system from its starting store to the changes that someone could observe.
Try this question. During one short run, the model receives 240 joules of electrical energy. The question states that 150 joules is transferred to the intended movement and 30 joules is transferred as sound. Account for the remaining energy. Subtract the two named transfers from the total. The remainder is 240 − 150 − 30 = 60 joules. If the problem says the remaining transfer heats the model and surroundings, state that 60 joules is transferred as thermal energy. Keep the explanation linked to the information supplied.
A student writes, “Ninety joules disappeared because the motor was inefficient.” Read the values again. Ninety joules is the total transferred as sound and heating in this simplified account. Those transfers can be less useful for the intended movement, but they are still part of the energy account. Revise the answer to identify where the energy went. If the question asks for only the thermal transfer, include the 60-joule result and its destination.
Now change the problem. A second model receives the same 240 joules, transfers 170 joules to movement and transfers 20 joules as sound. The remaining transfer is 50 joules. The second model has a larger named movement transfer for the same input in these stated runs. That supports a comparison of the given energy accounts. It does not tell you how far either model travelled, because the question gives no distance, load or route.
Check whether your boundary includes the object that changes
Suppose a moving toy climbs a small classroom ramp in a supervised demonstration. As its height increases, its gravitational potential energy increases. It may also continue moving. A response that mentions only movement misses the height change. Draw an outline around the objects described in the question, then name the changes that occur inside your chosen system.
For an independent attempt, consider a compressed spring launching a light model in a teacher’s demonstration. Name the starting energy store and two later transfers that a question could describe. A suitable answer begins with elastic potential energy and identifies kinetic energy of the moving model, with sound or thermal transfers where these occur. Explain the sequence with arrows or words. Your explanation should show the direction of change rather than simply list energy names.
Use power to compare the rate of transfer
Power describes how quickly energy is transferred. For a calculation with energy in joules and time in seconds, power is measured in watts. Write the relationship in words before entering numbers. Power equals energy divided by time. If you need energy, multiply power by time. If you need time, divide energy by power. The rearrangement should follow the quantity the question asks you to find.
A fictional display motor transfers 1,800 joules in 30 seconds. Its average power during that interval is 1,800 ÷ 30 = 60 watts. A second motor transfers the same 1,800 joules in 45 seconds, giving 40 watts. The first transfers the stated energy more quickly. If a question asks which uses more energy for those stated tasks, both use the same amount. Read the comparison word before deciding which number matters.
Try a problem with a hidden conversion. A small device operates at an average power of 25 watts for three minutes. Three minutes is 180 seconds. Its energy transfer is 25 × 180 = 4,500 joules. A first attempt of 75 joules came from multiplying 25 by 3 without changing the minutes. In the correction, put the conversion on its own line so that another reader can identify why the new answer differs.
Now consider an energy limit of 7,200 joules for a fictional classroom device transferring energy at 40 watts. Time equals 7,200 ÷ 40 = 180 seconds, or three minutes. Check the answer by multiplying 40 watts by 180 seconds to recover 7,200 joules. This reverse check is useful when the numbers are simple enough to calculate mentally.
Separate a rating from a particular measurement
A label may give a rated power under specified conditions. A question may instead give energy measured during an interval. If the problem tells you to assume constant operation at the rated power, use that assumption. If it gives an average measured energy transfer, use the measured values for that interval. Write down which information your answer uses.
For practice, a device labelled 80 watts is modelled as operating at that power for 50 seconds. Calculate 4,000 joules. In a separate test it transfers 3,600 joules over 50 seconds. Its measured average power is 72 watts. Both results can be calculated from their own stated information. Ask what conditions were used before treating the difference as an error in the label.
Calculate electrical energy and a fictional cost
Electricity-use problems often express energy in kilowatt-hours. Keep kilowatts and hours together in that calculation. A 500-watt appliance has a power of 0.5 kilowatts. If the question says it operates steadily for two hours, its energy use is 0.5 × 2 = 1 kilowatt-hour. A kilowatt-hour is an amount of energy. A kilowatt identifies power.
Use this invented tariff for the next examples only. Each kilowatt-hour costs 30 cents, and the exercise ignores other charges. A fictional 60-watt display lamp operates for five hours. Its power is 0.060 kilowatts. The energy used is 0.060 × 5 = 0.30 kilowatt-hours. At the given tariff, the cost is 0.30 × 30 cents = 9 cents. Keep the unit attached to the tariff until the final line.
Compare it with a 12-watt lamp operating for the same five hours under the exercise’s assumptions. Energy use is 0.012 × 5 = 0.060 kilowatt-hours. The cost is 1.8 cents. The difference is 7.2 cents for the stated operating period. To compare how well they serve a room, you would also need information about their light output and use. The calculation alone compares electrical energy and cost.
A student multiplies 60 by 5 and then by 30 to obtain 9,000 cents. The first product is 300 watt-hours. The tariff applies to kilowatt-hours. Divide by 1,000 before applying it. One useful repair is to write three headings across the page, power in kilowatts, time in hours, and energy in kilowatt-hours. Put each converted value under its heading before using the tariff.
Work backwards from a budget
A fictional display has a 90-cent energy allowance at the same 30-cent tariff. The allowance corresponds to 3 kilowatt-hours. If the combined power is 0.5 kilowatts, the permitted operating time in the simplified exercise is 3 ÷ 0.5 = 6 hours. State that the answer follows the supplied constant-power assumption.
For an independent check, use a 200-watt device for one hour and 30 minutes. Convert to 0.2 kilowatts and 1.5 hours. Energy use is 0.3 kilowatt-hours and the fictional cost is 9 cents. Explain why one hour and 30 minutes is 1.5 hours. A calculator entry of 1.30 would represent a different duration in decimal hours.
Read series circuits by following one complete path
In a series arrangement, the components lie along one path. Begin at one terminal of the source and trace the route through each component to the other terminal. A circuit diagram uses symbols to represent these connections. The positions of symbols on the page can vary. The connection pattern determines the arrangement.
Consider a classroom diagram with a cell, switch, lamp and resistor in a single complete loop. An ammeter at one point reads 0.20 amperes. In the stated series circuit, the current is 0.20 amperes at the other points too. A pupil claims that less current returns to the cell after passing through the lamp. Ask them to distinguish current from the energy transferred by the circuit. The series current relationship remains the same around the loop.
A second example has a 6.0-volt source and two series components. The voltage across one is 2.0 volts. The voltage across the other is 6.0 − 2.0 = 4.0 volts in the simplified circuit. Show the sum as a check. If a third component is added, use the voltages actually given rather than assuming that every component has an equal share.
Now suppose three identical resistors are connected in series and the question asks what happens to effective resistance as another resistor is added. Effective resistance increases. If asked to compare arrangements without numerical resistances, a clear qualitative statement is enough. Keep the number of components, their arrangement and the source information visible while you explain.
Match the measuring instrument to the quantity
An ammeter measures current and is included in the path whose current is being measured. A voltmeter measures the potential difference across a component, so its two connections span that component. In a paper exercise, point to the two locations the voltmeter connects before naming the reading.
This workbook uses diagrams described in words and supplied readings. Any construction or meter use should follow your teacher’s classroom instructions and approved equipment. For an independent paper check, describe a voltmeter connected across the first of two series lamps. Would moving one voltmeter connection so it spans both lamps measure the same thing? It would now measure the voltage across the pair. Identify what the instrument spans before using a value.
Follow the branches in a parallel circuit
In a parallel arrangement, current can follow separate branches between common junctions. Trace each branch and identify where the currents divide and combine. The voltage across branches connected across the same source is the same. The total current from the source is the sum of the branch currents.
Use this example. A source supplies two branches. One branch carries 0.30 amperes and the other carries 0.20 amperes. The source current is 0.50 amperes. If the source voltage is 6.0 volts, each branch connected across it has a voltage of 6.0 volts. Read the quantity in the question carefully. The two current values add. The branch voltage is identified through the connection.
Now a third branch carries 0.10 amperes in a stated test. The source current becomes 0.30 + 0.20 + 0.10 = 0.60 amperes. Adding a parallel branch decreases the effective resistance of the arrangement. If a question gives new measured currents, use those values for the new state. A real source and components can have limitations, so explain the idealised circuit the question supplies.
For a household-appliance discussion, parallel connections allow appliances to receive the supply voltage and be controlled on their own branches. If one appliance is switched off, the other complete branches can continue operating. A student answer that says only “parallel is better” needs the advantage named. State the feature and explain how it helps the use described.
Repair a diagram-reading error
Imagine the source current is 0.80 amperes and one branch current is 0.35 amperes. A student adds them and gives 1.15 amperes for the other branch. The source current already includes both branches. Subtract to obtain 0.45 amperes for the missing branch. Check by adding 0.35 and 0.45 to recover 0.80.
Try another with three branches. The source supplies 1.20 amperes, while two branches carry 0.25 and 0.40 amperes. The remaining branch carries 0.55 amperes. Draw a large junction and label arrows with the values. If your answer makes the branch larger than the whole source current, stop and reconsider which value represents the total.
Connect voltage and current to electrical power
Electrical power can be calculated by multiplying current by voltage. If voltage is in volts and current is in amperes, the result is in watts. Write the unit names beside the numbers when a question gives several readings. A voltage reading and a current reading should refer to the relevant device or part of the circuit.
A fictional 12-volt device takes a current of 2.0 amperes while operating under the stated conditions. Its electrical power is 12 × 2.0 = 24 watts. In 50 seconds at this constant power, the energy transferred is 24 × 50 = 1,200 joules. The first calculation finds a rate. The second combines that rate with a time.
Now the same type of question asks for current. A device operates at 18 watts from a 6.0-volt source. Current equals power divided by voltage, so the current is 18 ÷ 6.0 = 3.0 amperes. Multiply the answer by 6.0 volts to check that the power returns to 18 watts. A calculation that multiplies 18 by 6 gives the wrong relationship for the requested quantity.
A device label can contain several numbers. In a paper problem, identify the voltage rating and power rating the question wants you to use. If it asks which device has the larger rated power, compare watts after converting any kilowatts. If it asks which transfers more energy during use, include operating time. A lower-power device used for much longer can transfer more energy overall.
Test a two-device comparison
Device A operates at 30 watts for four minutes. Its energy transfer is 30 × 240 = 7,200 joules. Device B operates at 45 watts for two minutes. Its energy transfer is 45 × 120 = 5,400 joules. Device B has the higher power in the example, while Device A transfers the greater total energy over its stated interval.
For an independent attempt, change A’s duration to three minutes and B’s to the same three minutes. Their energy transfers become 5,400 joules and 8,100 joules. The equal-duration comparison now follows the power comparison. Explain which feature changed between the two questions and why it affected the result.
Explain generation and transmission as a sequence
An explanation of electricity generation should identify the changes at each stage. For a fossil-fuel power station described in a question, the fuel stores chemical energy. Burning transfers energy through heating, and the system uses that transfer to drive a turbine. The generator transfers energy electrically. Follow the equipment named in the source rather than adding unprovided details.
Consider an invented question with three cards. Card A says fuel is burned. Card B says a turbine turns. Card C says a generator supplies electricity. Arrange them in order, then write the main energy changes. A suitable response moves from chemical energy through thermal transfer to kinetic energy of the turbine and electrical energy transferred from the generator.
The transmission part of K123 includes the use of high-voltage lines and step-up and step-down transformers. At a given transmitted power, a higher voltage goes with a lower current. Lower current reduces heating losses in the transmission lines. A step-up transformer raises voltage before long-distance transmission, while step-down transformers reduce voltage for later distribution or use. Connect each device to its purpose in the sequence.
Use supplied values to make the comparison concrete. A simplified system transfers 6,000 watts. At 300 volts, current is 6,000 ÷ 300 = 20 amperes. At 3,000 volts, current is 6,000 ÷ 3,000 = 2 amperes. Both pairs give the same power when multiplied. The higher-voltage case has the lower current. Use that relationship to support the explanation about reduced line heating.
Keep a supplied comparison within its scope
A question might provide a table showing 500 joules transferred as heating in one set of lines and 100 joules in another under stated conditions. You can calculate a 400-joule difference and identify which set has the smaller loss. The readings alone do not tell you the complete design of a national grid. Explain the feature the question is using to illustrate transmission.
For a changed exercise, a system transfers 12,000 watts at either 600 volts or 6,000 volts. The corresponding currents are 20 amperes and 2 amperes. Show the calculation, then explain the repeated pattern. Keeping the power fixed lets the question isolate the connection between voltage and current. Your explanation should name that fixed condition.
Read waves using one feature at a time
A wave can transfer energy. A vibration can generate a wave in a rope or spring in a demonstration. When reading a drawn wave, distinguish amplitude, wavelength and frequency. Amplitude concerns the maximum displacement from the rest position. Wavelength concerns the spacing between corresponding points on successive waves. Frequency concerns the number of complete cycles each second.
Imagine a diagram showing a wavy line above and below a horizontal rest line. The top of a crest is four grid squares above the rest line. Each square represents 0.5 centimetres. The amplitude is 2.0 centimetres. The distance from a trough to a crest spans twice the amplitude in this symmetrical drawing. If you measure that full height and report it as amplitude, your answer doubles the intended quantity.
Now the horizontal spacing from one crest to the next is six squares, and each horizontal square represents three centimetres. The wavelength is 18 centimetres. Check whether the question gives the same scale on both axes. A diagram can use one scale vertically and another horizontally. Read each scale next to the direction you are measuring.
For a frequency example, a marked point completes 24 full vibrations in six seconds. Frequency is 24 ÷ 6 = 4 hertz. The counted quantity is the number of complete cycles. If a student counts every movement from one extreme to the other as a full cycle, they need to inspect how the question defines one repetition.
Compare two records without mixing the features
Record A shows an amplitude of two centimetres and a frequency of three hertz. Record B shows an amplitude of one centimetre and a frequency of five hertz. B has the greater frequency. A has the greater amplitude. A sentence saying “B is bigger” leaves the comparison unclear. Name the measured feature.
In an independent example, a rope point completes 35 full vibrations in seven seconds. The frequency is five hertz. Another point completes 30 in ten seconds, giving three hertz. The first vibrates more frequently in these records. You have no amplitude information, so you cannot use these counts to compare amplitude.
Match a wave application to the information supplied
The syllabus asks students to recognise uses of different types of waves. A practice question can combine a familiar purpose with a short description of the system. Begin by reading the application and then choose the category asked for. An example of a named use is enough when the instruction says “state”. A question asking for reasoning needs a connection to the details provided.
Imagine a set of fictional information cards for a school display. One describes a remote control sending a signal to a receiver. Another describes a broadcasting system carrying radio programmes. A third describes light travelling through an optical fibre. Match these applications to infrared, radio waves and light respectively. State the particular use rather than listing every wave name you remember.
Now read a short passage saying that a communication system uses a satellite link and a microwave signal. If asked to identify the wave in that system, use microwaves. If asked to name another use of microwaves from the syllabus, a microwave oven is a valid example. The shared category does not mean the two devices have the same construction, power or purpose.
A common weak answer adds claims beyond the question. A pupil might recognise ultraviolet as a wave used in some sterilisation systems and then say every ultraviolet source makes a room safe. The application example supports identifying a use. Evaluating a particular product would require further information. In a science answer, keep the explanation as precise as the evidence permits.
Practise reading a technology statement
Use this invented statement. “The inspection system uses X-rays to produce an image of the inside of a component.” A suitable answer identifies an engineering application of X-rays. A second statement says, “A remote sends a signal to a television receiver using infrared.” Identify the wave and describe its communication role in that statement.
For review, create three new cards from the applications your class has covered. Put the application on one side and the wave type on the other. When testing yourself, explain the connection aloud before turning the card. If two cards use the same wave type, say what differs about their purposes. This develops a more useful memory than a list without context.
Describe what a force changes
A force can change an object’s motion, direction, shape or size, or produce a turning effect. Start with what the question says happened to the object. If a moving object slows, name the speed change. If its path bends while its speed stays the same, name the direction change. Both are changes in motion.
Consider a fictional trolley demonstration. In Trial A, a stationary trolley begins moving after a push. In Trial B, a moving trolley slows when a force acts against its motion. In Trial C, a force guides it around a bend. Describe the effect in each case. A begins motion from rest, B decreases speed and C changes direction. An answer of “the force moves it” is too broad to distinguish the three trials.
For a shape example, a teacher presses a soft modelling block and its dimensions change. A response can state that the force changes the block’s shape or size, using the observed detail. If the block later returns to its original shape, include that only when the question asks about the later stage or supplies that observation.
A turning effect can be described through an everyday hinge or pivot. Pushing a door at a point farther from its hinge can make turning easier for the same applied force, provided the direction of the push is suitable. In K123, the moment is treated through its turning effect without requiring an equation. A word explanation should name the pivot, position of force and resulting turn.
Keep the story of the object consistent
Suppose a picture shows someone turning a tap handle. Identify the turning effect on the handle. A second picture shows a sponge being squeezed. Identify the change in shape. A third shows a bicycle following a curved path. Identify the change in direction. These are separate observations even though all involve forces.
For an independent answer, imagine a ball initially rolling straight across a level floor. A side push changes its direction. The question gives no speed readings. State that its direction changes, and avoid deciding whether its speed increases or decreases without supporting information. A precise answer can be short when it matches the observed change exactly.
Calculate a whole journey before dividing
Average speed is total distance divided by total time taken. First decide what belongs to the journey. Include pauses when the stated total interval includes them. Use consistent units for the distance and time. A question giving metres and seconds produces metres per second.
A fictional model cart travels 18 metres in 12 seconds, then remains stationary for six seconds, then travels another 12 metres in 12 seconds. The total distance is 30 metres. The total elapsed time is 30 seconds. The average speed for the whole record is 30 ÷ 30 = 1 metre per second. The pause is part of the stated record.
A student averages the two moving speeds. The first segment is 1.5 metres per second and the second is 1 metre per second, so they obtain 1.25 metres per second. That calculation ignores the pause and does not use the whole record. Even when there is no pause, an ordinary average of segment speeds needs conditions that the question may not give. The reliable starting point is total distance and total time.
Now calculate the average speed only while the cart is moving in this example. The moving distance is still 30 metres and the moving time is 24 seconds. The result is 1.25 metres per second. This is a different question with a different time interval. Put a box around the words that specify the interval before calculating.
Check a journey in kilometres and hours
A fictional vehicle travels 6 kilometres in 15 minutes. Fifteen minutes is one quarter of an hour, so its average speed is 24 kilometres per hour. If the question wants metres per second, use 6,000 metres and 900 seconds to obtain approximately 6.67 metres per second. Keep the conversion consistent from start to finish.
For a changed question, a model travels 42 metres in 28 seconds, pauses for seven seconds, then travels 18 metres in 15 seconds. The full distance is 60 metres and full time is 50 seconds. Average speed is 1.2 metres per second. Explain why the seven-second pause belongs in the denominator for the whole record.
Read acceleration and distance-time graphs
Acceleration describes change in speed over time for the one-direction motion considered here. Use final speed minus initial speed, then divide by the time taken. A value in metres per second divided by seconds gives metres per second squared. A negative result can indicate a decrease in speed when using the stated positive direction.
A model increases its speed from 2 metres per second to 8 metres per second in three seconds. The change is 6 metres per second, so acceleration is 2 metres per second squared. The calculation 8 ÷ 3 misses the starting speed. Write both speeds on separate lines before subtracting.
A second model slows from 9 metres per second to 3 metres per second over two seconds. Acceleration is (3 − 9) ÷ 2 = −3 metres per second squared. Explain that the speed decreases by 3 metres per second each second in this stated interval. If the question asks for the magnitude of deceleration, it is 3 metres per second squared. Follow the wording and sign convention given.
For a distance-time graph, a rising straight section represents distance increasing at a steady rate. A horizontal section represents no increase in distance during that interval. A steeper straight section has a greater gradient and represents a higher speed. Read the axis labels and scales before comparing the appearance of two lines.
Use points to support a graph statement
Suppose the plotted points are zero seconds and zero metres, five seconds and ten metres, ten seconds and ten metres, and fifteen seconds and twenty-five metres. The first interval has speed 2 metres per second. The second is stationary. The final interval has speed 3 metres per second. Total distance is 25 metres over 15 seconds, giving an average of about 1.67 metres per second.
If the question asks which interval is fastest, identify the final five seconds and show the distance increase of 15 metres over five seconds. A response that says “the highest point” confuses distance with speed. Use a change in distance over a change in time. For another attempt, alter the final point to twenty metres. The first and final moving intervals then have equal speed.
Combine the ideas in a fictional display investigation
A school display uses a small battery model to carry a message card along a marked route. The teacher supplies the following invented record. The model receives 3,600 joules in 120 seconds, travels 24 metres, and pauses for 20 seconds within that interval. The source voltage is 6 volts and the average source current is 5 amperes under the question’s simplified assumptions. Find average electrical power and average speed for the whole interval.
From energy and time, power is 3,600 ÷ 120 = 30 watts. From voltage and current, power is 6 × 5 = 30 watts. These two routes agree. Whole-interval average speed is 24 ÷ 120 = 0.20 metres per second. Moving-time average speed would use 100 seconds and give 0.24 metres per second. Label which speed you calculate.
A second record uses the same total time and distance but gives 4,200 joules of input. The average input power is 35 watts. The whole-interval average speed remains 0.20 metres per second. A pupil claims the higher-power run must have travelled faster. The records do not support that claim. Use the given distance and time for speed, and use the energy and time for average power.
The display designer wants evidence about why the second run required more energy. Possible next questions concern the route, load, surfaces, components and measurement conditions. The two records alone do not identify the cause. A sensible response names a factor to investigate and describes the information needed. For example, compare runs with the same load and route while checking energy and time consistently.
Finish with an answer you can defend
Write three short statements from this investigation. One should be a calculation, one a comparison and one a limitation. A suitable set is “The first run’s average input power was 30 watts.” “Both records have the same whole-interval average speed of 0.20 metres per second.” “The records do not establish the cause of the difference in energy input.”
Take one corrected exercise back to school if the reasoning remains unclear. Ask about the precise step, such as choosing the interval, reading the branch current or identifying the wave scale. For the next attempt, change the figures and explain the method before calculating. The goal is an answer that connects the correct quantity, a valid method and the actual question. Use the Punggol first-term learning guide for help organising that practice into a manageable week.
Use a short practice paper to identify the next repair
Set aside a short ordinary practice period and attempt the following questions without reading the answers first. These questions are original exercises for this workbook. They sample a few decisions from Machines Around Us (II). They do not reproduce the length, balance or digital interaction of either national paper. Put one line of reasoning beside each answer, even when you think the calculation is easy.
Question one gives a fictional lamp with a power of 18 watts operating for four minutes. Find its energy transfer in joules. Question two describes a source supplying two parallel branches, carrying 0.12 amperes and 0.18 amperes. Find the source current. Question three gives a total source voltage of 9 volts across two series components and a voltage of 4 volts across the first. Find the voltage across the second.
Question four describes a model travelling 16 metres in eight seconds, stopping for four seconds and travelling eight metres in another eight seconds. Calculate its whole-interval average speed. Question five asks for the acceleration of a model whose speed increases from 1 metre per second to 7 metres per second over three seconds. Question six describes a wave point completing 18 full vibrations in three seconds. Find its frequency.
The first answer is 18 × 240 = 4,320 joules. Four minutes supplies the conversion to 240 seconds. The second answer is 0.30 amperes, found by adding the branches. The third answer is 5 volts, because the two component voltages add to the stated 9 volts. Explain why addition is used for one question and subtraction for the next. The relationship tells you how to use the given quantities.
For question four, the total distance is 24 metres and the total time is 20 seconds. Average speed is 1.2 metres per second. Question five gives an acceleration of 2 metres per second squared. Question six gives a frequency of 6 hertz. If your numerical answer differs, check the interval, subtraction or conversion before repeating the entire exercise. Record the first point where your working changed.
After the check, choose one question to alter. Keep the type of question but change a single value. For example, change the pause in question four from four seconds to eight seconds. The full time becomes 24 seconds, and average speed becomes 1 metre per second. Describe why the extra pause reduced the average speed while total distance stayed the same. That changed example shows whether you can reuse the reasoning.
Make corrections show the decision you changed
A correction is easier to use later when it preserves the reason for the change. Begin with the original question and your first attempt. Find the earliest line that no longer matches the quantities or relationships in the prompt. Write a brief note beside that line. “I used the total current as another branch” identifies a different problem from “I added 0.12 and 0.18 incorrectly.” Each needs its own follow-up exercise.
Suppose your first energy answer is 72 joules for the 18-watt lamp used for four minutes. The operation 18 × 4 matches the numbers you copied, but the time unit is still minutes. Your correction can say “Watts are joules each second, so convert four minutes to 240 seconds.” On a later attempt, use a 15-watt lamp for two minutes. The answer is 1,800 joules. Ask whether you remembered the conversion before using the calculator.
In a circuit correction, draw the junction or the series loop again. Add only the values needed for the relationship. For a missing branch current, label the total before subtracting the known branch. For a voltage split in series, mark the source voltage separately from each component voltage. The drawing helps you see whether the value is a whole or one part. The same distinction appears in several calculations across the course.
For a written explanation, underline the scientific claim and circle the supporting detail. A response such as “The object has greater power” is incomplete when the question asks you to justify a comparison from energy and time. Add the energy transferred per unit time, or calculate both powers and compare them. If the question asks you to describe an observed movement, choose the actual change in speed, direction or shape before adding a cause.
Parents can help by asking the student to explain the changed line. Let the student point to the unit, branch, interval or graph scale that controls the answer. If they cannot yet explain it, keep the question for the subject teacher and note what they tried. A focused question might be “I understand the source current is shared, but I cannot tell which values already include both branches.” That gives a teacher a concrete starting point.
Revisit the correction after a gap using a fresh problem. A student who can read a model solution immediately may still need practice recognising the same decision independently. Keep the retry short enough to finish and discuss. Save the first attempt and the later response as a pair. When you plan the next week, choose the concept that still needs a clearer explanation and combine it with a topic your child can already handle confidently.

