This Top 100 Secondary 4 G2 Vocabulary List for Punggol helps students turn Design and Technology ideas into clear explanations: identify a user’s need, compare possible solutions, describe materials and mechanisms, and explain what a test shows. Each term has a plain meaning and an original example. The aim is to use the right word to make a decision understandable, not to decorate a drawing with technical language.
The guide supports students preparing for 2027 SEC G2 Design and Technology, syllabus K234, and parents helping them understand schoolwork. Begin with the terms connected to the current task, explain them aloud and apply them to a different example. These 100 words and phrases are an eduKate teaching selection, not an official SEAB compulsory word list, a popularity ranking or a prediction of examination questions.
- For: Secondary 4 students taking G2 Design and Technology and parents supporting independent learning.
- Inside: 100 terms for needs, research, ideas, drawings, people, materials, processes, mechanisms and control systems.
- Learning sequence: meaning, example, distinction, decision and a fresh application.
- Practical value: worked reasoning, common confusions, original practice and explained answers.
- Coursework: keep observations, decisions and project evidence authentic and follow the school’s supervision and assistance rules.
- Workshop work: use only teacher-approved materials, tools, equipment and procedures with the required supervision.
- Scope check: examination year 2027; checked on 16 November 2026.
Choose your reading route
Start with the task you need today, then return to the full guide when you are ready.
- Understand the scope — Check the subject, syllabus year and starting point.
- Learn the 100 terms — Use the numbered lists, meanings and original examples.
- See the words in use — Follow explanations and original worked examples.
- Practise and check — Try the questions before reading the explained answers.
- Plan the next lesson — Use the revision routine and parent guidance.
Article contents
Chapters 1–4
Chapters 5–8
Chapters 9–12
A student may know the word prototype but still be unable to explain what their model is meant to test. Another may describe a material as strong when the actual concern is whether a thin panel bends too much. In both cases, the vocabulary problem lies in the relationship between the word and the decision.
Begin with a question: what are you trying to find out? A drawing might clarify an arrangement. A measurement might establish whether something fits. A mock-up might reveal an awkward reach. A material comparison might identify a suitable property. The most useful term is the one that makes that purpose clearer.
Official scope, checked 16 November 2026: the 2027 K234 syllabus assesses design thinking and practical application of technology. Paper 1 is a 90-minute written examination worth 40%; Paper 2 is an individual design project worth 60%, conducted over 20 weeks excluding school holidays. G2 includes materials, workshop processes, mechanisms, control systems and adapting available electronic kits, including sensing and counting. The design journal records development as it happens. Use the school’s current instructions for the project, supervision and permitted assistance. The SEAB G2 directory identifies the subject and examination-year document.
G2 is the level of the subject taken. It does not describe every subject a student studies or decide the value of the student’s ideas. Check the actual subject code and examination year before reusing older notes. This vocabulary guide is a support resource, not the full syllabus or a substitute for school directions.
Read a small connected group first. For each entry, explain the example in your own words and then change one condition. Does the same term still apply? If you are unsure, identify the part that changed. That is usually a better starting point than copying the definition several times.
Jump to a word group: 1–10: Needs and requirements · 11–20: Research and evidence · 21–30: Ideas and decisions · 31–40: Drawings and communication · 41–50: People, models and checking · 51–60: Properties and consequences · 61–70: Material families and examples · 71–80: Planning and making language · 81–90: Mechanisms and movement · 91–100: Systems and control
1–10: Needs and requirements
A design begins with a situation worth understanding. These words help separate the user’s actual difficulty, the intended improvement and the requirements used to judge an idea.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 1 | Design opportunity | A situation in which a useful improvement might be made through design. | A student repeatedly loses track of task cards. Investigate the activity before assuming that a larger storage box is the answer. |
| 2 | User | The person who will interact with or use the proposed product. | A handle that suits its designer may not suit the intended user. Name whose needs the decision is meant to address. |
| 3 | Need | Something the user requires to carry out an activity or resolve a difficulty. | Needing to identify cards quickly differs from wanting a particular colour. Explain the underlying activity before choosing a feature. |
| 4 | Design brief | A concise statement describing the design intention, user and relevant situation. | A brief should explain what improvement is sought. It should not prematurely lock every detail to the first idea sketched. |
| 5 | Design specification | A set of requirements used to guide and assess the developing design. | Replace “small enough” with an appropriate measurable size limit where the investigation supports one. Explain why that requirement matters. |
| 6 | Criterion | A feature or standard used when judging an idea or outcome. | Ease of identifying each compartment could be a criterion. Decide what evidence would show whether the feature works for the user. |
| 7 | Constraint | A limit within which the design must be developed. | A limited available desk area constrains size. A good-looking option still needs revision if it cannot fit the intended space. |
| 8 | Function | What a product or part is intended to do. | A divider separates groups of cards. Its colour may help identification, but the physical separation is a different aspect of its function. |
| 9 | Aesthetics | The sensory and expressive qualities of a design, including how its appearance is experienced. | Colour, form and surface finish can affect how a product is perceived. Attractive does not automatically mean usable or suitable. |
| 10 | Context of use | The circumstances in which a product will be used, including its surroundings and activity. | A tabletop organiser used in a shared study area faces different space and access conditions from one kept inside a drawer. |
11–20: Research and evidence
Research earns its place when it informs a decision. Keep the difference between what was recorded, what was inferred and what remains uncertain visible in your explanation.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 11 | Research | A purposeful investigation to obtain information relevant to a design decision. | Researching a material is useful when it answers a particular question. A collection of unrelated product photographs does not automatically provide that answer. |
| 12 | Observation | Recording what happens during an activity without replacing it with an unsupported explanation. | “The card fell when the folder moved” records an event. “The user is careless” adds a judgement that the observation does not establish. |
| 13 | Interview | A conversation using questions to understand a person’s experience, needs or views. | Ask how the person currently stores the cards. A leading question about your favourite idea may produce less useful information. |
| 14 | Survey | A structured way of gathering responses from a group of people. | State who responded and what was asked. Five convenient respondents cannot automatically represent every student in Punggol. |
| 15 | Product analysis | Examining an existing product to understand its features, operation and suitability. | Ask what a compartment does and why its shape matters. Listing colours without connecting them to use gives little design insight. |
| 16 | User analysis | Examining the intended user’s relevant characteristics, activities and needs. | Consider the user’s task and interaction with the product. Do not invent difficulties or personal characteristics to make an idea appear necessary. |
| 17 | 5W1H | A questioning framework using who, what, when, where, why and how. | “Where are the cards used?” may reveal a space constraint. The framework helps inquiry; answering every heading mechanically is not the goal. |
| 18 | PMI | A way to examine plus points, minus points and interesting aspects of an idea. | A wider base may improve one feature while occupying more space. Record the tension instead of treating every feature as an advantage. |
| 19 | SWOT analysis | An analysis of strengths, weaknesses, opportunities and threats in a stated situation. | Explain each point in relation to the design context. An impressive heading does not make an unsupported claim into evidence. |
| 20 | Evidence | Information that supports or challenges a claim or decision. | A measured footprint supports a size comparison. It does not by itself prove that the product is comfortable or stable. |
21–30: Ideas and decisions
Generating alternatives and selecting among them are different activities. Use these words to explain how an idea changes and why one direction deserves further development.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 21 | Ideation | Generating and exploring possible responses to a design opportunity. | Produce alternatives that differ in useful ways, such as access or arrangement. Redrawing one layout in three colours may explore only appearance. |
| 22 | Brainstorming | Generating a range of ideas before narrowing and developing them. | Record possibilities without pretending they are already workable. Later checks can identify which ideas deserve further attention. |
| 23 | SCAMPER | An idea-generation framework prompting changes such as substitution, combination, adaptation, modification, reuse, elimination and rearrangement or reversal. | Ask whether removing an unnecessary part could simplify access. A prompt creates a possibility, not proof of improvement. |
| 24 | Shape borrowing | Using a shape from another object or context as a starting point for an idea. | A folded leaf shape might suggest a divider arrangement. The borrowed appearance still needs to be developed for the actual task. |
| 25 | Concept | An initial idea for how a design could address the need. | A rotating holder is a concept, not yet a complete solution. Dimensions, access and operation still require investigation. |
| 26 | Alternative | A different possible way of addressing the same design intention. | A sliding tray and a fixed set of compartments can be compared against the same need. Compare their consequences, not only their novelty. |
| 27 | Refinement | A considered improvement to an idea based on what has been learned. | Increasing a slot’s clearance may improve access. Check that the change does not create a new problem elsewhere. |
| 28 | Feasibility | Whether an idea can reasonably be carried out under the relevant conditions. | An idea may be attractive but unsuitable for the available materials, time or school facilities. Identify the actual limiting condition. |
| 29 | Trade-off | A situation in which improving one aspect involves giving up something in another. | Adding compartments can increase organisation while reducing space in each compartment. Explain both effects before choosing the arrangement. |
| 30 | Justification | A reasoned explanation of why a decision fits the evidence and requirements. | “I chose it because it is better” lacks the connection. Name the requirement, the relevant feature and the evidence supporting the choice. |
31–40: Drawings and communication
Different drawings answer different questions. Choose the representation that reveals the needed information; no single attractive view communicates every size, relationship and movement.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 31 | Sketch | A quick drawing used to explore or communicate an idea. | A rough sketch can reveal an access problem before details are settled. Its value depends on the thinking it enables, not decorative neatness alone. |
| 32 | Isometric drawing | A pictorial drawing using three principal axes 120° apart and the same scale along each axis. | It can help communicate overall form. An isometric view is not automatically a complete set of dimensions for making the product. |
| 33 | Perspective drawing | A drawing method that represents depth, with receding features appearing smaller and parallel directions often converging. | Use it to communicate how a product may look. Do not measure an apparent length from perspective as though every direction has one constant scale. |
| 34 | Orthographic projection | Representing an object through separate views looking straight at its faces. | Front, side and plan views reveal different dimensions. Check that corresponding features agree across the views. |
| 35 | Exploded view | A drawing showing components separated to make their arrangement and relationships clearer. | An exploded view can clarify where a divider belongs. The gaps shown between components do not mean those gaps remain after assembly. |
| 36 | Working drawing | A drawing communicating technical information needed to make or assemble the design. | A useful working drawing includes relevant dimensions and details. A polished presentation view may serve a different purpose. |
| 37 | Dimension | A stated measurement describing the size or position of a feature. | Write the unit and identify what the measurement refers to. An overall width and a clear internal width are not necessarily equal. |
| 38 | Scale | The stated relationship between a drawing’s dimensions and the corresponding real dimensions. | At a scale of 1:2, a 90-millimetre drawn length represents 180 millimetres. Scale does not change the intended real product size. |
| 39 | Annotation | A note attached to a drawing to explain a feature, action or decision. | “Divider separates current and completed cards” explains function. Repeating the visible colour without adding meaning may not help the reader. |
| 40 | Materials list | A record of the materials and relevant quantities or sizes required for the planned work. | Name what is needed clearly enough to support planning. A list of materials is not evidence that all have already been used. |
41–50: People, models and checking
A model is useful because it helps answer a question. Be precise about the intended user and the limits of what the model can establish.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 41 | Ergonomics | Designing interactions and products to suit people, their activities and the conditions of use. | Check whether the intended user can see, reach and operate the holder comfortably. A pleasing shape alone does not establish a good fit. |
| 42 | Anthropometric data | Measurements of human body dimensions used to inform design decisions. | Hand dimensions may inform an opening or grip. One convenient person’s measurement does not represent the whole intended user group. |
| 43 | Clearance | Space allowed between parts, or between a person and a feature, for the intended fit or movement. | A six-millimetre card stack in an eight-millimetre slot has two millimetres of total clearance. That is not two millimetres on each side. |
| 44 | Reach | The distance or area a person can access in a particular posture and situation. | A compartment can be visible but awkward to reach. Consider the actual arrangement instead of relying on a drawing viewed from above. |
| 45 | Grip | The way a person holds or controls an object. | A rounded shape may change the grip, but suitability still depends on size, surface and task. Avoid assuming one handle fits everyone. |
| 46 | Mock-up | A model made to explore a particular feature, question or arrangement. | A paper model can help compare compartment layouts. It cannot automatically establish how a different final material will withstand use. |
| 47 | Prototype | A model built to investigate how a proposed design will work or perform. | A prototype can reveal a problem and lead to revision. Calling it a prototype does not mean it has passed every test. |
| 48 | Testing | Checking a feature or performance through an appropriate planned activity or measurement. | Decide what will be checked before judging the outcome. A demonstration that looks successful may leave an important requirement untested. |
| 49 | Evaluation | Judging how well an idea or outcome meets relevant requirements using evidence. | State what worked, what remains uncertain and what needs improvement. Evaluation is more informative than listing praise for the finished object. |
| 50 | Iteration | Returning to an idea or stage, making a change and checking the result again. | A revised divider opening needs another relevant check. Iteration describes purposeful development, not repeated redrawing with no new question. |
51–60: Properties and consequences
Strength, stiffness, toughness and hardness describe different aspects of behaviour. Connect the property to a particular condition instead of treating them as interchangeable compliments.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 51 | Strength | A material’s ability to withstand stress without failing under specified conditions. | A stronger material does not automatically make every possible shape stronger. Dimensions, loading and joints also affect the product’s performance. |
| 52 | Stiffness | Resistance to deformation under an applied load. | A part can be stiff yet brittle. Do not use stiffness as a substitute for toughness when the concern is resistance to impact damage. |
| 53 | Toughness | A material’s ability to absorb energy before fracturing. | A component facing impacts may need toughness. A hard surface does not, by itself, establish that the component resists fracture. |
| 54 | Hardness | Resistance to local surface deformation, such as indentation or scratching. | Hardness can matter for a surface that is contacted repeatedly. It does not mean that the material is impossible to bend or break. |
| 55 | Elasticity | The ability to return towards the original shape when a deforming load is removed, within the elastic range. | A spring can recover after suitable loading. This does not mean any amount of stretching will be reversible. |
| 56 | Durability | The ability to remain useful over time under the expected conditions. | Consider wear, repeated use and the environment. A material name alone cannot establish how long an assembled product will last. |
| 57 | Thermoplastic | A plastic that can soften when heated and harden again on cooling within suitable processing conditions. | Acrylic is an example. Material processing needs appropriate equipment and supervision; the term is not an instruction to heat plastic at home. |
| 58 | Thermoset | A plastic that forms a permanently set network when cured and cannot be remelted and reshaped like a thermoplastic. | A melamine product illustrates the material category. Heating a thermoset is not a useful way to make it mouldable again. |
| 59 | Composite | A material combining distinct constituents to achieve useful combined properties. | Glass-reinforced plastic combines glass fibres with a polymer matrix. Its performance depends on the constituents and how they are arranged. |
| 60 | Sustainability | Considering longer-term environmental, social and resource consequences of a design and its use. | Repairability and material use can matter alongside initial cost. Calling a product green requires reasons, not merely a green colour or natural appearance. |
61–70: Material families and examples
A material category provides a starting point for comparison. Grade, size, form, construction and use conditions still matter. These examples are not instructions to handle materials without supervision.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 61 | Natural timber | Wood obtained from a tree and used with its characteristic grain structure. | Pine and meranti are examples. Grain direction can affect behaviour, so a material decision should consider more than appearance. |
| 62 | Plywood | A board made from bonded layers of wood veneer, commonly arranged with adjacent grain directions crossing. | Layer arrangement helps explain why plywood differs from a solid piece of timber. Grade and construction still affect suitability. |
| 63 | Medium-density fibreboard | An engineered board formed from wood fibres bonded with resin, commonly abbreviated MDF. | Its relatively uniform structure can be useful in suitable work. It is not automatically suitable for wet conditions; follow school material guidance. |
| 64 | Veneer | A thin sheet of wood used alone in a construction or bonded to another material. | A wood-faced board may have a veneer surface rather than being solid timber throughout. Describe the structure accurately. |
| 65 | Ferrous metal | A metal or alloy in which iron is the main metallic constituent. | Mild steel is ferrous. Do not define the group only by whether a sample is attracted to a magnet. |
| 66 | Non-ferrous metal | A metal or alloy whose main metallic constituent is not iron. | Aluminium and copper are examples. The category does not guarantee identical weight, strength or corrosion behaviour. |
| 67 | Alloy | A metallic material made by combining a metal with one or more other elements. | Brass combines copper and zinc. An alloy’s properties depend on composition and processing; alloy is not a synonym for steel. |
| 68 | Mild steel | A low-carbon steel used in many general engineering applications. | Its usefulness depends on the part and conditions. Consider corrosion protection where relevant rather than assuming an unfinished part suits every environment. |
| 69 | Aluminium | A metal with relatively low density, used in many forms and alloys. | A low-density material may help reduce mass. The thickness, shape and joining method still affect whether the proposed part works. |
| 70 | Acrylic | A thermoplastic often used where transparency and an appropriate surface finish are useful. | A clear panel can make contents visible. Check impact and other requirements rather than assuming transparent materials are interchangeable. |
71–80: Planning and making language
These words help a student understand how information becomes planned work. They do not replace training in the actual equipment, approved process or safe workshop routine.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 71 | Datum | A reference point, line or surface from which measurements or positions are taken. | Using a consistent reference helps related features line up. Changing the reference halfway through can introduce inconsistent positions. |
| 72 | Marking out | Transferring required measurements and positions onto a workpiece before an appropriate process. | Accuracy begins before shaping. The actual tools and method must suit the material and follow the teacher’s instructions. |
| 73 | Tolerance | The permitted variation from a specified dimension or requirement. | A stated size allowance defines acceptable variation. It is different from an unnoticed measuring mistake or the clearance intentionally designed between parts. |
| 74 | Joining | Connecting components so that they form an intended assembly. | Choose a joining approach for the materials and purpose. A joint that is suitable for one pair of materials may fail with another. |
| 75 | Adhesive | A substance used to bond surfaces together. | Compatibility and intended use matter. Follow the school’s approved product and handling instructions instead of assuming one adhesive bonds everything safely. |
| 76 | Fastener | A component used to hold parts together, such as a screw, bolt or rivet. | Some fasteners permit convenient disassembly and others do not. Name the particular fastening method when discussing repair or replacement. |
| 77 | Finishing | Treating a surface to improve an appropriate quality, such as appearance or protection. | A finish may change appearance or resistance to conditions. It cannot compensate for an unsuitable design or an uncorrected unsafe feature. |
| 78 | Gantt chart | A chart showing planned activities against time, often using horizontal bars. | Use it to notice delays and revise the plan. Drawing a neat chart once does not demonstrate continued monitoring. |
| 79 | Flowchart | A diagram showing the order of actions and, where relevant, decision branches. | A flowchart can clarify a process. It does a different job from a Gantt chart, which makes the timing of activities visible. |
| 80 | Design journal | A record showing the development of the student’s design thinking, decisions and work as the project progresses. | Keep authentic evidence of changes. A later polished story must not replace what actually happened or invent earlier observations. |
81–90: Mechanisms and movement
Trace what moves first, what connects the parts and what moves next. Mechanism names become easier to use when linked to a clear account of motion.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 81 | Lever | A relatively rigid member that turns about a pivot to transmit an action. | The positions of the pivot, effort and load affect what the lever does. A lever does not always multiply force. |
| 82 | Linkage | An arrangement of connected members and joints used to transmit or change movement. | A linkage can coordinate the movement of parts. Sketch the relevant positions to explain its action instead of relying on its name alone. |
| 83 | Screw mechanism | A mechanism using a helical thread to relate rotary movement and linear movement. | A threaded adjustment can move a part along a line when turned. Explain which part rotates and which part moves along the axis. |
| 84 | Rack and pinion | A mechanism combining a straight toothed rack and a rotating toothed gear. | Rotation of the pinion can move the rack in a straight line. The input can also be reversed in suitable arrangements. |
| 85 | Pulley | A wheel used with a belt, rope or cable to transmit motion or redirect an applied action. | A pulley arrangement may change direction or movement. Do not assume every single pulley reduces the effort needed by the same amount. |
| 86 | Cam | A shaped member whose movement controls the movement of a contacting follower. | A rotating cam can produce a repeated rise and fall. The profile influences the follower’s motion, not just the cam’s overall size. |
| 87 | Gear | A toothed wheel that meshes with another toothed component to transmit motion. | For two externally meshing gears, rotation directions are opposite. Tooth numbers help explain their relative rotation, rather than appearance alone. |
| 88 | Spring | A component that deforms elastically to store energy and provide a restoring action. | A spring can help return a part towards its starting position. It must suit the intended movement and load; more stretch is not automatically better. |
| 89 | Motion transmission | Passing movement from one part of a system to another. | A belt can transfer rotation between pulleys. The resulting speed or direction may differ, so trace the movement through the arrangement. |
| 90 | Motion conversion | Changing one type of motion into another. | A rotating pinion moving a rack converts rotary motion to linear motion. Name both the input motion and the output motion. |
91–100: Systems and control
Separate what enters a system, what acts on it and what comes out. Feedback has a particular role: it influences control using information about the result.
| No. | Term | Plain meaning | Use it accurately |
|---|---|---|---|
| 91 | Input | A signal, movement or other quantity entering a system. | In a light-sensing kit, detected light provides input information. The lamp or indicator that responds belongs to another part of the system. |
| 92 | Process | The part of a system that acts on input to determine an output. | A control circuit can use a sensor signal to decide an indicator’s state. Process does not simply mean any activity mentioned in the description. |
| 93 | Output | The resulting action, movement or information produced by a system. | A buzzer sounding is an output. Whether that output solves the user’s difficulty still needs a separate design judgement. |
| 94 | Feedback | Information about an outcome returned to influence how a system operates. | A measured temperature can be used to adjust control. Merely displaying a temperature does not automatically mean the system controls it. |
| 95 | Open-loop system | A system whose control action does not use feedback about the controlled result. | A simple timed action can continue without checking whether its intended result was achieved. A sensor elsewhere does not automatically make it closed-loop. |
| 96 | Closed-loop system | A system using feedback about the controlled result to adjust its operation. | A temperature-controlled system can compare a measured condition with the target. Explain the feedback relationship, not only the presence of a sensor. |
| 97 | Sensor | A device that responds to a physical quantity or condition and provides a usable signal. | A light sensor detects light conditions. It is not the same component as an indicator that communicates information to the user. |
| 98 | Counter | A device or system that records the number of defined events. | A kit may count each detected passage. The count is meaningful only if the event being detected has been identified clearly. |
| 99 | Rotary motion | Movement around an axis. | A gear rotates about its axis. Do not describe the whole connected mechanism as rotary if its output moves along a straight line. |
| 100 | Linear motion | Movement along a straight line. | A rack can move linearly. Back-and-forth movement along the same line is reciprocating motion, a more specific description when relevant. |
A brief is not a list of every dimension
A brief explains the intended design response in its context. Specifications turn relevant requirements into checks. Students often jump directly to dimensions because numbers feel precise. Precision is useful only when the number answers a real need. Ask what evidence supports the size and what would happen if that requirement were not met.
Strong and stiff do not mean the same thing
A part may bend noticeably without breaking. If the design concern is that it bends too far during use, stiffness is directly relevant. If the concern is failure under a load, strength is relevant. If the concern involves absorbing impact before fracture, toughness matters. The same product may need several properties, but the explanation should identify the particular problem.
A mock-up is not weak work
A simple model can answer an important question early. Its purpose might be to compare access to two compartments or establish whether a proposed arrangement fits the available area. It need not imitate every final feature. The mistake is claiming that a rough layout model has also proved durability, structural performance or the suitability of a different material.
Evaluation is not a final paragraph of praise
Evaluation connects evidence to requirements. A useful sentence identifies a feature, reports what the relevant check showed and explains the consequence for the design. The consequence can be a decision to retain a feature, revise it or investigate further. An honest uncertainty is more helpful than a confident claim with no supporting evidence.
Original fictional practice situation: a student wants a tabletop holder for three groups of task cards during a study activity. The written scenario says that the available area is 180 millimetres wide and 120 millimetres deep. This is an invented exercise in reading requirements, not a report of interviews, measurements or a live coursework assignment.
The need is to keep the three groups identifiable and accessible within the available space. “Make a colourful holder” starts with a feature but leaves the problem unclear. A more useful brief would identify the user, the sorting activity and the improvement sought. Detailed choices can then develop through comparison.
Turn the information into checks
One relevant size requirement is that the holder’s footprint must fit within the stated width and depth. Another concerns the cards. Suppose the exercise gives a stack of 15 cards, each 0.4 millimetres thick. Their combined thickness is 15 × 0.4 = 6 millimetres. An eight-millimetre opening would provide two millimetres of total clearance for that stack.
The calculation does not prove that the opening is convenient. Cards may need to be grasped, tilted or separated, and the surrounding shape matters. The calculation establishes a particular geometric relationship. A suitable model and appropriate user check would be needed to investigate access. This is a useful example of how a correct number can still leave a design question unanswered.
Compare two incomplete proposals
Proposal A has a stated footprint of 170 × 110 millimetres. Proposal B has a stated footprint of 190 × 100 millimetres. Both figures are invented. A fits within the given width and depth. B exceeds the available width by ten millimetres, even though its depth fits. B therefore needs revision before it can meet the stated space constraint.
This does not prove that A is the final answer. Its arrangement, access and other relevant qualities still need checking. Nor does it mean B has no useful ideas. A feature from B could inform a new alternative. The evidence supports a limited conclusion: A passes this dimensional check, while B does not in its present form.
Make the reason visible
A useful explanation is: “I would continue investigating Proposal A because its stated footprint fits within the available area. I still need to check whether the intended user can identify and remove the cards conveniently.” The sentence identifies the evidence, makes a decision and retains the unresolved question. It is more informative than saying A is better because it is smaller.
If the available area changes, the comparison should be revisited. Requirements are not decorative notes attached after choosing a favourite idea. They guide the decision. Students become more confident when they can explain which fact would make them reconsider their choice.
CHAPTER 5 OF 12
5. Explain a material choice without turning a name into a guarantee
A material choice involves a proposed use, a relevant property and an expected consequence. “Acrylic is good” supplies none of those connections. “A transparent panel could help the user see the contents” identifies a possible benefit, but further questions remain about impact, shape, joints and the available school processes.
Likewise, selecting aluminium because of its relatively low density does not establish that every aluminium part will be lighter than every steel part. Dimensions and construction affect mass. A thin part of one material and a thick part of another are not a controlled comparison of material alone. Be clear about what is being compared.
For the fictional holder, a paper or card mock-up could investigate arrangement before a resistant material is selected. That reduces the amount of work committed to an untested layout. The model’s evidence must stay within its purpose. A convenient paper opening does not certify the performance of an eventual joint or surface.
Ask three questions when revising an explanation. Which property matters? Under what conditions does it matter? What other design feature could change the outcome? These questions help students move beyond memorising a list of advantages and disadvantages divorced from a particular product.
Workshop decisions also depend on the school’s approved materials, processes and supervision. Do not treat an online description as permission to machine, heat, bond or finish a material. Understanding a process term is different from being trained and authorised to carry out that process.
Start with the input motion and the required output motion. A hand turning a part gives rotary motion. A component moving along a straight path has linear motion. Back-and-forth movement along a line is reciprocating; movement to and fro through an angle is oscillating. These descriptions help students explain what a mechanism must accomplish.
A rack and pinion is useful for seeing rotary-to-linear conversion. The pinion rotates while its teeth engage the rack, which moves along a line. In a written explanation, name the moving components and the relationship between them. “The rack and pinion works” provides no account of the action.
For an original gear exercise, imagine two externally meshing gears. The driver has 12 teeth and the driven gear has 24 teeth. One complete driver revolution moves 12 teeth past the contact, corresponding to half a revolution of the driven gear. Four driver revolutions therefore correspond to two driven revolutions, in the opposite direction.
The tooth-count reasoning explains the movement relationship. It does not prove that a real assembly is safe, durable or suitable for a particular load. Keep those questions separate. The example is a paper exercise, not a construction instruction or a specification for a working machine.
A cam also encourages precise language. The cam’s profile controls how the contacting follower moves. A different profile can produce a different movement sequence. A student should describe that sequence rather than assume that every cam produces an identical rise, fall or pause.
Control-system vocabulary is easier when linked to a complete relationship. Identify the condition or action entering the system, what interprets or responds to it, and the resulting action or information. A sensor, an indicator and the user each play different roles.
Consider a general light-sensing kit used under school supervision. The sensor responds to light conditions; the control arrangement uses the resulting signal; an indicator provides an output. That description alone does not establish closed-loop control of light. To make that claim, the measured result must be fed back and used to influence the control action.
A temperature display provides a useful contrast with automatic temperature control. Both may measure temperature. A display communicates a value; a closed-loop controller uses feedback to adjust an action in relation to the intended condition. The presence of a sensor is therefore insufficient to decide whether a system is closed-loop.
For a counting task, define the event. Is one count intended for each object passing a point or each press of a button? If a detector responds twice to one intended event, the output may not represent what the user wanted to count. The vocabulary helps identify the question that needs checking; it does not establish a fix without examining the system.
Use the school-approved kit and instructions for practical work. This guide provides conceptual language and written examples. It does not supply circuit construction steps, changes to mains-powered appliances or permission to bypass equipment safeguards.
A useful design record allows another reader to follow a decision. What question was being considered? What was tried or examined? What was observed? How did that affect the next step? The record does not need to pretend that the first idea was perfect or that development happened in a straight line.
Suppose an ordinary classroom model reveals that a divider blocks access. A meaningful note records the issue, links it to the user’s task and explains the planned revision. A later check can show whether that revision addressed the issue. Replacing the record with a polished story in which the problem never happened removes useful evidence of thinking.
Keep plans live. A Gantt chart can show whether an activity is taking longer than expected, while a smaller sub-plan can clarify the next actions. A flowchart can explain an order or decision sequence. Choose the tool for the question rather than drawing both simply to fill space.
Parents can discuss general vocabulary, ask the student to explain a decision and help them organise an agreed study routine. They should not invent user research, prepare fabricated test results, create an assessed prototype on the student’s behalf or rewrite the journal as though the work were the student’s own. Follow the school’s directions on support, attribution and permitted digital tools.
The fictional holder exercise in this article is for practising language and reasoning. Do not submit its invented situation, dimensions or conclusions as personal project evidence. Actual coursework must develop from the examination task, the student’s own investigation and the authorised school process.
Attempt these original questions before reading the explanations. They are teaching exercises, not official examination items. A short, accurate answer is often more useful than a paragraph containing several technical terms whose relationships are unclear.
- A requirement says that an organiser must fit a 160-millimetre-wide space. A proposal is 175 millimetres wide. What kind of requirement is involved, and what conclusion does the measurement support?
- A student says a panel needs greater toughness because it bends too much under ordinary use without breaking. Which property is more directly connected to the stated concern?
- A model shows that a compartment layout fits the desk. Does that prove that the final material and joints will be durable? Explain.
- On a drawing made at a scale of 1:2, a line representing an edge measures 75 millimetres on the page. No dimension label is given. What real edge length does that represent?
- A stack is six millimetres thick and its opening is nine millimetres wide. Calculate the total clearance.
- Explain why an exploded view should not be read as a drawing of the final spaces between assembled parts.
- Two externally meshing gears have 10 and 20 teeth. If the 10-tooth driver makes six revolutions, how many revolutions does the other gear make, and in which relative direction?
- A temperature sensor supplies a value to a display. What further relationship would be needed to establish closed-loop temperature control?
- An entry says, “The prototype was excellent.” Identify two kinds of information that would make the evaluation more useful.
- A student discovers a problem after making a mock-up. Is returning to an earlier idea necessarily a failure of the design process? Explain.
Answers and explanations
- The available width is a size constraint. The proposal exceeds it by 15 millimetres and needs revision to fit. The measurement does not judge every other aspect of the idea.
- Stiffness is directly relevant to resistance to deformation. Toughness concerns energy absorbed before fracture. The wording of the problem identifies the distinction.
- No. The model establishes information about the tested layout. Durability of different materials and joints needs relevant evidence; it cannot be inferred from fit alone.
- 150 millimetres. At 1:2, the drawing is half the corresponding real size. This question gives a measured drawing length, not a dimension label; a dimension label normally states the intended real size.
- Three millimetres of total clearance. Do not describe it as three millimetres on each side.
- The components are deliberately separated to show their arrangement and relationships. The depicted separation is a communication device, not necessarily an assembly gap.
- Three revolutions, in the opposite direction. Six × 10 ÷ 20 = 3. This applies to the stated pair of externally meshing gears.
- The measured condition must be fed back and used to adjust control in relation to the target. Displaying a measurement alone does not show that relationship.
- Name the relevant requirement and give evidence from an appropriate check. Then explain what the evidence supports, what remains uncertain or what should change.
- No. A useful observation can justify reconsidering an earlier decision. Explain what was learned and why the next revision follows from it.
Classify mistakes before choosing another task. A wrong term may need a contrast. A correct term with no supporting reason needs an explanation exercise. A correct explanation attached to an unsupported claim needs an evidence check. These are different difficulties, even when they lead to the same incomplete answer.
Choose four or five related terms and apply them to one small example. Brief, specification, criterion and constraint make a useful group. Strength, stiffness, toughness and hardness make another. Ask the student to explain one distinction and show why it matters in a design situation.
After reading, close the list. Give a fresh scenario and ask which term fits. Invite the student to sketch if that makes the relationship clearer. Then ask them to explain the sketch in one accurate sentence. This connects meaning, representation and communication without turning every session into a large project.
Keep a short correction record: the initial misunderstanding, the repaired idea and a new application. “I called every material strong” identifies a pattern. The next action is to name the particular property and connect it to a stated condition. The fresh example checks whether the correction can be used independently.
Revisit earlier terms after a gap and mix them with current topics. A student who can recognise a word only beside its original definition still needs practice choosing it. Remove prompts gradually. A useful learning sequence makes the next attempt manageable while asking the student to do more of the thinking.
Listen for the place where the explanation becomes uncertain. If the student cannot identify the need, return to the activity and the user. If they can describe the need but choose features without reasons, compare alternatives against requirements. If they can draw the idea but cannot explain how it operates, trace the movement or information through the system.
When additional teaching support is considered, bring a specific example of the difficulty, the current school topic and the student’s own attempt. Ask how the teacher will diagnose the misunderstanding and check transfer to a new situation. Ask how the support respects coursework independence and the school’s practical arrangements.
A parent does not need to select the material or solve the design. Useful questions include: “What are you trying to find out?”, “Which evidence supports that choice?”, “What does this model not tell you yet?” and “What would make you revise the idea?” These questions keep responsibility with the student while making the reasoning easier to discuss.
For the wider course context, continue to the G2 Design and Technology syllabus guide for Punggol. Keep this vocabulary resource alongside the student’s school materials and the current examination-year document.
Checked 16 November 2026. The official documents establish the subject and assessment context. The vocabulary selection, examples, invented measurements and practice questions are original teaching material and do not cover every syllabus outcome.
- SEAB: 2027 SEC G2 syllabuses for school candidates — confirm the subject, code and year.
- SEAB: K234 G2 Design and Technology syllabus for 2027 — consult the scope and current project requirements. The document’s cover identifies 2027.
More Secondary 4 G2 vocabulary guides
Choose the guide that matches the subject you are studying. Each list teaches the words through meanings, examples and practice.
- Additional Mathematics vocabulary
- Literature in English vocabulary
- Art vocabulary
- Humanities (Social Studies, History) vocabulary
- Nutrition and Food Science vocabulary
- Computing vocabulary
- Principles of Accounts vocabulary
- Humanities (Social Studies, Geography) vocabulary
- Science (Physics, Chemistry) vocabulary
- Mathematics vocabulary
- English Language vocabulary
