Small Group Tutorials

Here to help students catch up, keep up, and move ahead. Book a consultation here.

How Can G3 Physics Tuition Help My Child Predict a Potential-Divider Output When the Light Changes?

Three learners review open books together at a classroom table, with stacks of textbooks, stationery and a whiteboard in the bright room.

Did you know? A light-dependent resistor does not make every potential-divider output rise when light gets brighter. The direction depends on where the output is measured. G3 Physics tuition can help by diagnosing whether your child is confused about the sensor, the series circuit or the chosen output points.

Your immediate next step is to circle the two components and mark exactly where the voltmeter is connected. Then ask: “Which component’s resistance changed, and is the output measured across that component?” This usually reveals the hidden mistake faster than another page of calculations.

G3 names the subject level, not the student’s Posting Group. Confirm the school’s actual Physics arrangement and examination year before using any tuition worksheet or syllabus code.

G3 PHYSICS ORIENTATION

eduKate Punggol Science Tuition · 11-second introduction

Follow resistance, then voltage

Do not guess “brighter means higher”. Trace the component across which the output is taken.

Contents

The diagram-reading error behind many wrong answers

Students often memorise two isolated facts: an LDR’s resistance falls in brighter light, and potential difference is “shared”. Both are true, but neither identifies the output. A potential divider has two series components; the voltage across one can rise while the voltage across the other falls.

A tutor should watch the child begin. Does the child label the LDR response correctly? Does the child recognise a series circuit? Does the child treat the output as the voltage across a named component rather than a floating number? The correction belongs at the first failed step.

Back to contents

A three-step method that survives a flipped circuit

  1. State the sensor change. Brighter light means lower LDR resistance; darkness means higher LDR resistance.
  2. Locate the output. Identify whether it is measured across the LDR or the fixed resistor.
  3. Compare the shares. In a two-resistor series divider, the larger resistance has the larger share of the supply voltage.

The tutor then flips the LDR and fixed resistor. If the student repeats the same prediction, the method has not transferred. Guided questions should fade until the student annotates the diagram and explains the direction without help.

Where a three-student lesson is genuinely available, students can compare three circuits with the same components but different output points. One predicts, one challenges the reasoning and one checks with a ratio. The value is rapid contrast, not generic extra worksheets.

Back to contents

Worked example: what happens when the room gets brighter?

Imagine a 6 V supply with an LDR and a fixed resistor in series. The output is measured across the fixed resistor. In darkness, suppose the LDR has the larger resistance. It takes a larger share of the 6 V, so the fixed resistor has a smaller output voltage.

When the room becomes brighter, the LDR resistance falls. The fixed resistor is now a larger fraction of the total resistance, so the voltage across it rises. If the output were measured across the LDR instead, the trend would reverse.

A numerical check can confirm the reasoning: Vout = Vsupply × Routput ÷ Rtotal. The equation should verify the prediction, not replace the diagram reasoning.

Back to contents

How this fits 2027 G3 Physics

For 2027 school candidates, G3 Physics is syllabus K323. Under D.C. Circuits, the official syllabus includes variable potential dividers, negative-temperature-coefficient thermistors and light-dependent resistors as input transducers in potential dividers, together with simple circuit problems.

Use the official 2027 SEAB G3 Physics K323 syllabus. This topic is about predicting and explaining circuit behaviour; it is not a licence to assume that every school or tuition provider offers separate G3 Physics support.

Back to contents

What independent progress looks like

  • The student labels the output points before calculating.
  • The student states the sensor-resistance change in words.
  • The predicted trend reverses correctly when the components or output points are swapped.
  • A calculation and a qualitative explanation agree.
  • The student can handle a thermistor variant without copying the LDR rule.

Tuition can expose misconceptions and sequence practice, but the student still needs to draw, annotate and check circuits independently. A useful delayed check uses a fresh diagram in which the sensor sits in the opposite position. If the explanation remains correct, the learning has travelled.

For the force-analysis branch of the same subject, read Vectors, Resultant Forces, Free-Body Diagrams and Equilibrium.

Back to contents

Continue from here: Start Here · Tuition · Education · Pathways · Parenting 101 · All Site Routes

eduKate Punggol

Contact

83 Punggol Central, Singapore 828761

edu|Kate Bukit Timah

8 Fourth Avenue, Singapore 268674

By Appointment +65 8823 1234
admin@edukatesg.com

Email Us

When a child finally understands, school becomes less frightening and the future opens wider. Email us for the latest schedules and fees.

← 返回

感谢您的回复。 ✨